| EBECRYL® 575 | Allnex | EBECRYL® 575 is a chlorine free polyester resin diluted with EBECRYL® 892. It has been specifically designed to provide good adhesion to plastic substrates. Films of EBECRYL®575 cured by ultraviolet light (UV) or electron beam (EB) result in good hardness...view more EBECRYL® 575 is a chlorine free polyester resin diluted with EBECRYL® 892. It has been specifically designed to provide good adhesion to plastic substrates. Films of EBECRYL®575 cured by ultraviolet light (UV) or electron beam (EB) result in good hardness. view less | Request Sample |
| EBECRYL® 5850 | Allnex | EBECRYL® 5850 is a high performing medium viscosity bio-based diacrylate. When properly formulated, coatings and inks based on EBECRYL®5850 cured by ultraviolet light (UV) or electron beam (EB) energy display high reactivity with good hardness and scratch...view more EBECRYL® 5850 is a high performing medium viscosity bio-based diacrylate. When properly formulated, coatings and inks based on EBECRYL®5850 cured by ultraviolet light (UV) or electron beam (EB) energy display high reactivity with good hardness and scratch resistance. view less | Request Sample |
| EBECRYL® 600/35 OT | Allnex | EBECRYL® 600-35 OT is the diacrylate ester of bisphenol A epoxy resin diluted with 35% of oligotriacrylate (OTA 480). This resin is characterized by its low odour, light colour, low irritancy and fast cure response. Films of EBECRYL® 600/35OT cured by exp...view more EBECRYL® 600-35 OT is the diacrylate ester of bisphenol A epoxy resin diluted with 35% of oligotriacrylate (OTA 480). This resin is characterized by its low odour, light colour, low irritancy and fast cure response. Films of EBECRYL® 600/35OT cured by exposure to ultraviolet light (UV) and electron beam (EB) exhibit high surface hardness and gloss, low residual odour and the excellent solvent resistance typical of epoxy resins. view less | Request Sample |
| EBECRYL® 6100 | Allnex | EBECRYL® 6100 is an epoxy dimethacrylate oligomer without monomers or diluting oligomers. EBECRYL® 6100 is recommended for use in applications where high temperature resistance or high hardness are needed. | Request Sample |
| EBECRYL® 611 | Allnex | EBECRYL® 611 is an epoxy dimethacrylate oligomer without monomers or diluting oligomers. EBECRYL® 611 is recommended for use in applications where high temperature resistance or high hardness is needed. | Request Sample |
| EBECRYL® 716 | Allnex | EBECRYL® 716 is a chlorine-free inert binder diluted with TMPTA. It has been specifically designed to provide good adhesion to non-corona treated rigid plastic substrates. | Request Sample |
| RAYLOK™ C1102 | Allnex | RAYLOK™ C1102 is a styrene free urethane acrylate based resin providing high glass transition temperature combined with good flexibility upon curing. This resin is specially developed for making glass fibre composites which are to be cured by Ultraviolet ...view more RAYLOK™ C1102 is a styrene free urethane acrylate based resin providing high glass transition temperature combined with good flexibility upon curing. This resin is specially developed for making glass fibre composites which are to be cured by Ultraviolet (UV) light. view less | Request Sample |
| UVEKOL® A | Allnex | Uvekol® A is a one-component acrylic resin for the lamination of glass systems. It is cured by UV light for 20 minutes. The Uvekol® A interlayer produces glass laminates with excellent acoustic performance. It can be applied with nearly all kinds of glass...view more Uvekol® A is a one-component acrylic resin for the lamination of glass systems. It is cured by UV light for 20 minutes. The Uvekol® A interlayer produces glass laminates with excellent acoustic performance. It can be applied with nearly all kinds of glass: flat and slightly bent, tempered, coated, and other types. view less | Request Sample |
| UVEKOL® FR-C | Allnex | Uvekol® FR-C is a mono-component acrylic resin designed for glass lamination especially developed to confer safety impact resistance to fire resistant ceramic glass. The laminates made of this computer are cured under UV light for 20 minutes. The glass la...view more Uvekol® FR-C is a mono-component acrylic resin designed for glass lamination especially developed to confer safety impact resistance to fire resistant ceramic glass. The laminates made of this computer are cured under UV light for 20 minutes. The glass lamination process using Uvekol® FR-C is simple and does not require heating or pressure. view less | Request Sample |
| UVEKOL® S | Allnex | UVEKOL® S is a one-component acrylic resin for the lamination of glass systems. It is cured under UV light for 20 minutes. The UVEKOL® S interlayer produces glass laminates with excellent impact resistance. It can be applied with nearly all kinds of glass...view more UVEKOL® S is a one-component acrylic resin for the lamination of glass systems. It is cured under UV light for 20 minutes. The UVEKOL® S interlayer produces glass laminates with excellent impact resistance. It can be applied with nearly all kinds of glass: flat and bent, tempered, coated and other types of glass. view less | Request Sample |
| UVEKOL® S 15 | Allnex | Uvekol® S 15 is a one-component acrylic resin for the lamination of glass systems. It is cured under UV light for 20 minutes. The Uvekol® S 15 interlayer produces glass laminates with excellent impact resistance. It can be applied with nearly all kinds of...view more Uvekol® S 15 is a one-component acrylic resin for the lamination of glass systems. It is cured under UV light for 20 minutes. The Uvekol® S 15 interlayer produces glass laminates with excellent impact resistance. It can be applied with nearly all kinds of glass: flat and bent, tempered, coated, and other types of glass. view less | Request Sample |
| WorléeCryl® 8025 | Worlée-Chemie G.m.b.H. | WorléeCryl® 8025 is an aqueous acrylic solution, free of emulsifier, that can be used for the production of flexographic and gravure inks and overprint varnishes. The use of W´Cryl 8025 is specially recommended for systems in which combustible solvents sh...view more WorléeCryl® 8025 is an aqueous acrylic solution, free of emulsifier, that can be used for the production of flexographic and gravure inks and overprint varnishes. The use of W´Cryl 8025 is specially recommended for systems in which combustible solvents should be eliminated. It is a ready-to-use solution. view less | |
| WorléeDur D 46 | Worlée-Chemie G.m.b.H. | WorléeDur D 46 is a short oil epoxy ester based on conjugated drying fatty acids. It is used in air-drying and stoving finishes with outstanding adhesion, rapid drying and good chemical resistance. W´Dur D 46 is compatible with unplasticized urea and mela...view more WorléeDur D 46 is a short oil epoxy ester based on conjugated drying fatty acids. It is used in air-drying and stoving finishes with outstanding adhesion, rapid drying and good chemical resistance. W´Dur D 46 is compatible with unplasticized urea and melamine formaldehyde resins. W´Dur D 46 is an excellent binder for quick-drying primers and top-coats with very good adhesion and chemical resistance. Zinc-rich primers based on W´Dur D 46 have very good stability and anticorrosive properties. view less | |
| WorléeKyd C 640 | Worlée-Chemie G.m.b.H. | WorléeKyd C 640 is a short oil, non-drying alkyd intended for use with nitrocellulose for the manufacture of high quality modified nitrocellulose finishes. This grade has a non-volatile content of 60% ±1. W´Kyd C 640 is compatible with the majority of sho...view more WorléeKyd C 640 is a short oil, non-drying alkyd intended for use with nitrocellulose for the manufacture of high quality modified nitrocellulose finishes. This grade has a non-volatile content of 60% ±1. W´Kyd C 640 is compatible with the majority of short and medium oil length drying and non-drying alkyds. W´Kyd C 640 is particularly suitable for the manufacture of high quality nitrocellulose finishes for wood and paper. The solvent release is very fast. view less | |
| WorléePol® 230 | Worlée-Chemie G.m.b.H. | WorléePol® 230 is a low viscous and solvent free branched polyol with ester and ether groups used for the formulation of solvent free coatings, sealings, and adhesives. It is especially suitable as a hydrophobic basic binder for chemical and mechanical we...view more WorléePol® 230 is a low viscous and solvent free branched polyol with ester and ether groups used for the formulation of solvent free coatings, sealings, and adhesives. It is especially suitable as a hydrophobic basic binder for chemical and mechanical wear-resistant coatings, e.g. for concrete, asphalt and steel. Adding W´Pol 230 to systems based on W´Pol 165 results in better mechanical and chemical resistance. view less | |
| WorléePol® 808 | Worlée-Chemie G.m.b.H. | WorléePol® 808 is a highly reactive, low viscous polyester, which is partially water thinnable. It is used as a plastification compound in water thinnable, acid curing, or stoving finishes for paper, foils etc.. Another use of W´Pol 808, also in combinati...view more WorléePol® 808 is a highly reactive, low viscous polyester, which is partially water thinnable. It is used as a plastification compound in water thinnable, acid curing, or stoving finishes for paper, foils etc.. Another use of W´Pol 808, also in combination with suitable amino resins, is the production of high gloss, heat curing overprint varnishes and inks. view less | |
| WorléeSin MS 235 | Worlée-Chemie G.m.b.H. | WorléeSin MS 235 is an alcohol soluble maleic resin that is water thinnable after neutralisation. It is suitable for the production of flexographic and gravure inks for paper, aluminium and plastic films. Due to its compatibility with nitro- and ethyl cel...view more WorléeSin MS 235 is an alcohol soluble maleic resin that is water thinnable after neutralisation. It is suitable for the production of flexographic and gravure inks for paper, aluminium and plastic films. Due to its compatibility with nitro- and ethyl cellulose and with softeners, inks and varnishes based on W´Sin MS 235 exhibit a high gloss level and excellent transparency. Good pigment grinding is also observed. view less | |
| WorléeSin MS 265 | Worlée-Chemie G.m.b.H. | WorléeSin MS 265 is a hard, spirit soluble maleic resin which becomes water thinnable after neutralization. It is used to formulate water thinnable flexo printing inks with very fast drying and increased abrasion resistance. This product is applied in fle...view more WorléeSin MS 265 is a hard, spirit soluble maleic resin which becomes water thinnable after neutralization. It is used to formulate water thinnable flexo printing inks with very fast drying and increased abrasion resistance. This product is applied in flexo and gravure inks and overprint lacquers. view less |
