| ANTI-TERRA®-203 | BYK | ANTI-TERRA®-203 is a solution of an alkylammonium salt of a polycarboxylic acid. This product is suitable for medium to low polar solvent-borne and solvent-free coating systems. It causes an increase in thixotropy. In highly filled systems, the sagging te...view more ANTI-TERRA®-203 is a solution of an alkylammonium salt of a polycarboxylic acid. This product is suitable for medium to low polar solvent-borne and solvent-free coating systems. It causes an increase in thixotropy. In highly filled systems, the sagging tendency is reduced; in addition, no negative influence on the water sensitivity of the paint film has been observed. When formulated into anti-corrosion primers, the protective properties are enhanced in many instances. view less | |
| ANTI-TERRA®-204 | BYK | ANTI-TERRA®-204 is a solution of a polycarboxylic acid salt of polyamine amides. In comparison to ANTI-TERRA-203, ANTI-TERRA-204 can additionally be used in non-polar systems and is compatible with white spirits. The lower the polarity the more the thixot...view more ANTI-TERRA®-204 is a solution of a polycarboxylic acid salt of polyamine amides. In comparison to ANTI-TERRA-203, ANTI-TERRA-204 can additionally be used in non-polar systems and is compatible with white spirits. The lower the polarity the more the thixotropy is increased. The preferred binders are long, medium and short oil alkyds, PVC-copolymers, chlorinated rubber and epoxy. Even in "low-filled“ systems, the sagging tendency is reduced; in addition, no negative influence on the water sensitivity of the paint film has been observed. When formulated into anticorrosion primers, the protective properties are enhanced in many instances. view less | |
| ANTI-TERRA®-205 | BYK | ANTI-TERRA®-205 is a high molecular weight wetting and dispersing additives for solvent-borne systems. Solution of a polycarboxylic acid salt of polyamine amides. | |
| ANTI-TERRA®-250 | BYK | ANTI-TERRA®-250 is a solution of an alkylolammonium salt of a high molecular weight acidic polymer. It is used in aqueous systems and provides an increase in thixotropy and prevents hard settling of pigments. Due to controlled flocculation mechanism, the ...view more ANTI-TERRA®-250 is a solution of an alkylolammonium salt of a high molecular weight acidic polymer. It is used in aqueous systems and provides an increase in thixotropy and prevents hard settling of pigments. Due to controlled flocculation mechanism, the use of ANTI-TERRA-250 may lead to a minor gloss reduction. view less | |
| ANTI-TERRA®-U | BYK | ANTI-TERRA-U is the standard wetting and dispersing additive for solvent-borne industrial and architectural coatings. It can also be utilized to provide excellent gelling in organo-philic bentonites. This product is composed of a solution of a salt of uns...view more ANTI-TERRA-U is the standard wetting and dispersing additive for solvent-borne industrial and architectural coatings. It can also be utilized to provide excellent gelling in organo-philic bentonites. This product is composed of a solution of a salt of unsaturated polyamine amides and lower molecular weight acidic polyesters. view less | |
| ANTI-TERRA®-U 100 | BYK | ANTI-TERRA-U 100 is the solvent-free version of ANTI-TERRA U , the standard wetting and dispersing additive for solvent-borne industrial and architectural coatings. It can also be used to provide excellent gelation of organophilic bentonites. ANTI-TERR...view more ANTI-TERRA-U 100 is the solvent-free version of ANTI-TERRA U , the standard wetting and dispersing additive for solvent-borne industrial and architectural coatings. It can also be used to provide excellent gelation of organophilic bentonites. ANTI-TERRA-U 100 is effective for wetting and dispersing colored pigments, both organic and inorganic. No adverse effect has been observed on the pot-life of two-component systems or on the dry time of oxidative cure binders. ANTI-TERRA-U 100 can also be used as a wetting and suspending additive in water soluble coatings. view less | |
| AQUACER 1013 | BYK | AQUACER 1013 is a VOC-free HDPE-based wax emulsion for improving the surface protection in aqueous coatings and printing inks as well as in aqueous care products and polishes. | |
| AQUACER 1031 | BYK | AQUACER 1031 is an emulsion based on a polyethylene wax for improving the surface properties of aqueous care products. It offers an anti-slip effect and good foot traffic resistance. | |
| AQUACER 1039 | BYK | AQUACER 1039 is a paraffin wax emulsion for improved surface characteristics in aqueous coatings and printing inks. | |
| AQUACER 1040 | BYK | AQUACER 1040 is a primary polyethylene dispersion for formulating release agents for metal die casting. | |
| AQUACER 1061 | BYK | AQUACER 1061 is an emulsion of an ethylene-acrylic acid copolymer wax for improving the surface characteristics of paper. | |
| AQUACER 1063 | BYK | AQUACER 1063 is a polyethylene dispersion to improve the anti-caking properties of hot-melt adhesives and to increase adhesion in dispersion adhesives for the packaging sector. | |
| AQUACER 1075 | BYK | AQUACER 1075 is an emulsion based on an HD polyethylene wax to improve the surface properties of aqueous care products and polishes, and aqueous printing inks. | |
| AQUACER 1510 | BYK | AQUACER 1510 is a polypropylene wax emulsion for aqueous glass fiber sizings to improve the mechanical properties in glass fiber- reinforced PP compounds. | |
| AQUACER® 1547 | BYK | AQUACER® 1547 is a wax emulsion for improving surface properties of water-borne can coatings. It is an anionic emulsion of an oxidized HD polyethylene wax. This product improves scratch resistance. | |
| AQUACER 2500 | BYK | AQUACER 2500 is a wax emulsion on the basis of modified PE for aqueous foil and paper coatings to improve slip and abrasion resistance. | |
| AQUACER 2650 | BYK | AQUACER 2650 is a wax emulsion based on carnauba wax for aqueous thermal transfer systems, car care products and aqueous leather coatings. It seals and thereby covers any minor scratches on the surface that is to be treated and restores the color of the s...view more AQUACER 2650 is a wax emulsion based on carnauba wax for aqueous thermal transfer systems, car care products and aqueous leather coatings. It seals and thereby covers any minor scratches on the surface that is to be treated and restores the color of the surface. The melting point of 85 °C means that the wax emulsion can easily be polished up using a soft terry cloth or microfiber cloth, but polishing with mechanical tools is also possible. view less | |
| AQUACER 3500 | BYK | AQUACER 3500 is a cationic wax emulsion based on a modified polypropylene wax for formulating release agents for metal die casting. | |
| AQUACER 494 | BYK | AQUACER 494 is an aqueous paraffin wax emulsion for care products and polishes. | |
| AQUACER 497 | BYK | AQUACER 497 is a paraffin-based wax emulsion for aqueous coatings, printing inks as well as care products and polishes for improving water repellency and surface slip. | |
| AQUACER 501 | BYK | AQUACER 501 is an HDPE-based wax emulsion for aqueous systems to improve surface protection. | |
| AQUACER 506 | BYK | AQUACER 506 is an emulsion based on a HD polyethylene wax for improving the surface properties of aqueous care products and polishes. It improves the buffability, increases filling capacity and produces an anti-slip effect. The above-mentioned properties ...view more AQUACER 506 is an emulsion based on a HD polyethylene wax for improving the surface properties of aqueous care products and polishes. It improves the buffability, increases filling capacity and produces an anti-slip effect. The above-mentioned properties are generated by mixing AQUACER 506 with polymers in a ratio of 3:1 (solid wax to solid polymer). A mixing ratio of 1:6 increases the water- and alcohol-resistance, the protection against heel marks (= foot traffic resistance), and the dirt-repellent action. AQUACER 506 is compatible with all known polymer dispersions and plasticizers. view less | |
| AQUACER® 507 | BYK | AQUACER® 507 is an anionic emulsion of an oxidized HD polyethylene wax. It is suitable for use in non-ionic and anionic water-borne automotive systems and industrial paints. This product enhances flip-flop effect, improves the D.O.I. of clear coats, enhan...view more AQUACER® 507 is an anionic emulsion of an oxidized HD polyethylene wax. It is suitable for use in non-ionic and anionic water-borne automotive systems and industrial paints. This product enhances flip-flop effect, improves the D.O.I. of clear coats, enhances hardness and slip, and reduces short wave defects (mottling, Bénard cells). view less | |
| AQUACER® 513 | BYK | AQUACER® 513 is a non-ionic emulsion based on an oxidized HD polyethylene wax. It is suitable for use in aqueous systems and printing inks. This product improves the following surface properties: scratch resistance in aqueous systems, rub resistance in pr...view more AQUACER® 513 is a non-ionic emulsion based on an oxidized HD polyethylene wax. It is suitable for use in aqueous systems and printing inks. This product improves the following surface properties: scratch resistance in aqueous systems, rub resistance in printing inks and black heel marking resistance in parquet lacquers. view less | |
| AQUACER 519 | BYK | AQUACER 519 is an emulsion based on a HD polyethylene wax for improving the surface properties of aqueous care products and polishes. It improves the buffability, increases filling capacity and produces an anti-slip effect. The above-mentioned properties ...view more AQUACER 519 is an emulsion based on a HD polyethylene wax for improving the surface properties of aqueous care products and polishes. It improves the buffability, increases filling capacity and produces an anti-slip effect. The above-mentioned properties are generated by mixing AQUACER 519 with polymers in a ratio of 3:1 (solid wax to solid polymer). A mixing ratio of 1:6 increases the water- and alcohol-resistance, the protection against heel marks (= foot traffic resistance), and the dirt-repellent action. AQUACER 519 is compatible with all known polymer dispersions and plasticizers. view less | |
| AQUACER® 526 | BYK | AQUACER® 526 is a wax emulsion for water-borne effect coatings. It is an emulsion of an anionic modified Ethylene-Vinyl Acetate-Copolymer wax (EVA). This product is suitable for water-borne top coats and base coats. It enhances flip-flop effect, improves ...view more AQUACER® 526 is a wax emulsion for water-borne effect coatings. It is an emulsion of an anionic modified Ethylene-Vinyl Acetate-Copolymer wax (EVA). This product is suitable for water-borne top coats and base coats. It enhances flip-flop effect, improves orientation of effect pigments (aluminum, mica, etc.), reduces short wave defects (mottling, Bénard cells), and there is no negative influence on chemical resistance. view less | |
| AQUACER 527 | BYK | AQUACER 527 is a wax emulsion based on a modified EVA copolymer wax to improve surface characteristics in aqueous coating systems and printing inks. | |
| AQUACER 528 | BYK | AQUACER 528 is an emulsion based on an ethylene-acrylic acid-copolymer wax for improving the surface properties of aqueous care products. It offers strong anti-slip effect and good foot traffic resistance. | |
| AQUACER 530 | BYK | AQUACER 530 is a wax emulsion for improved surface characteristics in aqueous printing inks, overprint varnishes, wood and furniture coatings as well as inkjet inks. | |
| AQUACER® 531 | BYK | AQUACER® 531is a wax emulsion for improving surface properties of water-borne industrial paints and printing inks. It is a non-ionic emulsion based on a modified polyethylene wax. This additive improves the following surface properties: slip, scratch resi...view more AQUACER® 531is a wax emulsion for improving surface properties of water-borne industrial paints and printing inks. It is a non-ionic emulsion based on a modified polyethylene wax. This additive improves the following surface properties: slip, scratch resistance, rub resistance and anti blocking. view less | |
| AQUACER 532 | BYK | AQUACER 532 is an emulsion of a modified HD polyethylene wax for improved surface characteristics in aqueous coating systems. | |
| AQUACER® 533 | BYK | AQUACER® 533 is a wax emulsion on the basis of modified paraffin for aqueous systems to improve surface slip, anti-blocking, and water-resistance. It is typically used in architectural coatings and in the printing inks industry. | |
| AQUACER® 537 | BYK | AQUACER® 537 is an anionic emulsion based on a modified paraffin wax. It is suitable for aqueous systems for furniture- and parquet, industrial- and decorative paints. This product improves the following surface properties: water repellency, anti blocking...view more AQUACER® 537 is an anionic emulsion based on a modified paraffin wax. It is suitable for aqueous systems for furniture- and parquet, industrial- and decorative paints. This product improves the following surface properties: water repellency, anti blocking and slip. view less | |
| AQUACER® 539 | BYK | AQUACER® 539 is a non-ionic emulsion based on a modified paraffin wax. This product is suitable for aqueous systems for furniture- and parquet, industrial- and decorative paints. It improves the following surface properties: slip, water repellency, anti b...view more AQUACER® 539 is a non-ionic emulsion based on a modified paraffin wax. This product is suitable for aqueous systems for furniture- and parquet, industrial- and decorative paints. It improves the following surface properties: slip, water repellency, anti blocking, scratch resistance, rub resistance and soft feel effect. view less | |
| AQUACER 541 | BYK | AQUACER 541 is an aqueous emulsion of a montan ester wax for care products and polishes as well as for aqueous coating systems and leather coatings. | |
| AQUACER® 552 | BYK | AQUACER® 552 is a non-ionic emulsion based on an oxidized HD polyethylene wax. This product is suitable for use in aqueous systems and printing inks. It is used to improve scratch resistance in aqueous systems. | |
| AQUACER 561 | BYK | AQUACER 561 is a beeswax-based wax emulsion to improve surface protection in aqueous care products and coating systems. | |
| AQUACER 565 | BYK | AQUACER 565 is an aqueous carnauba wax emulsion for improving the surface characteristics of care products, polishes, and leather coatings. It seals and thereby covers any minor scratches on the surface that is to be treated and restores the color of the ...view more AQUACER 565 is an aqueous carnauba wax emulsion for improving the surface characteristics of care products, polishes, and leather coatings. It seals and thereby covers any minor scratches on the surface that is to be treated and restores the color of the surface. The melting point of 85 °C means that the wax emulsion can easily be polished up using a soft terry cloth or microfiber cloth, but polishing with mechanical tools is also possible. view less | |
| AQUACER 570 | BYK | AQUACER 570 is a modified Ecolabel-compliant sunflower wax emulsion to improve the surface properties of care products and polishes. It seals and thereby covers any minor scratches on the surface that is to be treated, and restores the surface’s original ...view more AQUACER 570 is a modified Ecolabel-compliant sunflower wax emulsion to improve the surface properties of care products and polishes. It seals and thereby covers any minor scratches on the surface that is to be treated, and restores the surface’s original color. It also improves the hydrophobicity and the oleophobicity of care products and polishes. This product is recommended for maintaining and protecting all types of surfaces, for leather, coated and uncoated surfaces. view less | |
| AQUACER 571 | BYK | AQUACER 571 is a modified rice bran wax emulsion to improve the surface properties of care products, polishes, and aqueous coating systems. | |
| AQUACER 581 | BYK | AQUACER 581 is a wax emulsion based on carnauba wax for aqueous paper coatings to improve surface slip, scratch-resistance, uniformity of printing ink acceptance, and ink setoff. Anti-caking additive for thermoplastics and hotmelts. | |
| AQUACER 582 | BYK | AQUACER 582 is an emulsion based on a polyethylene wax for improving the surface properties of aqueous seed coatings. | |
| AQUACER 583 | BYK | AQUACER 583 is a wax emulsion used to improve the surface characteristics of seed coatings. | |
| AQUACER® 593 | BYK | AQUACER® 593 is a wax emulsion for improving anti slip of water-borne paint systems and printing inks. It is a non-ionic emulsion of a modified polypropylene wax. This product is suitable for use in non-ionic and anionic water-borne paint systems and prin...view more AQUACER® 593 is a wax emulsion for improving anti slip of water-borne paint systems and printing inks. It is a non-ionic emulsion of a modified polypropylene wax. This product is suitable for use in non-ionic and anionic water-borne paint systems and printing inks. view less | |
| AQUACER 595 | BYK | AQUACER 595 is an emulsion based on a modified polypropylene wax for improving the surface properties of aqueous care products. It offers a strong anti-slip effect and good dirt repulsion. In aqueous leather finishes it produces an anti-slip and anti-tack...view more AQUACER 595 is an emulsion based on a modified polypropylene wax for improving the surface properties of aqueous care products. It offers a strong anti-slip effect and good dirt repulsion. In aqueous leather finishes it produces an anti-slip and anti-tack effect. view less | |
| AQUACER 597 | BYK | AQUACER 597 is a cationic wax emulsion based on a modified polypropylene wax for formulating release agents for metal die casting. | |
| AQUACER® 840 | BYK | AQUACER® 840 is a cationic emulsion of an oxidized HD polyethylene wax. This product is suitable for use in non-ionic and anionic water-borne automotive systems and industrial paints. It enhances flip-flop effect, improves the D.O.I. of clear coats, impro...view more AQUACER® 840 is a cationic emulsion of an oxidized HD polyethylene wax. This product is suitable for use in non-ionic and anionic water-borne automotive systems and industrial paints. It enhances flip-flop effect, improves the D.O.I. of clear coats, improves orientation of effect pigments and reduces short wave defects. view less | |
| AQUAMAT® 208 | BYK | AQUAMAT® 208 is an oxidized HD polyethylene wax dispersion. It is suitable for aqueous systems e. g. furniture- and parquet lacquer, industrial- and decorative paints and inks. The additive improves the following surface properties: gloss reduction, scrat...view more AQUAMAT® 208 is an oxidized HD polyethylene wax dispersion. It is suitable for aqueous systems e. g. furniture- and parquet lacquer, industrial- and decorative paints and inks. The additive improves the following surface properties: gloss reduction, scratch resistance and soft feel effect. view less | |
| AQUAMAT® 263 | BYK | AQUAMAT® 263 is an oxidized HD polyethylene wax dispersion. This product is suitable for aqueous systems e. g. furniture- and parquet lacquer, industrial- and decorative paints and inks. The additive improves the following surface properties: gloss reduct...view more AQUAMAT® 263 is an oxidized HD polyethylene wax dispersion. This product is suitable for aqueous systems e. g. furniture- and parquet lacquer, industrial- and decorative paints and inks. The additive improves the following surface properties: gloss reduction, scratch resistance, soft feel effect, rub resistance, anti blocking and black heel resistance. view less | |
| AQUATIX® 8421 | BYK | AQUATIX® 8421 is a non-ionic emulsion of a modified Ethylene-Vinyl-Acetate (EVA) copolymer wax. It improves the rheological properties and brilliance of effect pigment slurries that are co-solvent-free. This product provides the following properties: impr...view more AQUATIX® 8421 is a non-ionic emulsion of a modified Ethylene-Vinyl-Acetate (EVA) copolymer wax. It improves the rheological properties and brilliance of effect pigment slurries that are co-solvent-free. This product provides the following properties: improves effect pigment orientation, reduces cloudiness /mottling, shows less sensivity to co-solvents in coating systems compared to PU based thickeners, is “ready to use”, provides easy handling and incorporation compared to clays or acrylic thickeners, and excellent anti-settling properties in coatings during storage and application. view less | |
| BENTOLITE-L 10 | BYK | BENTOLITE-L 10 is a low iron rheology additive based on natural bentonite for aqueous plastic refractories. | |
| BENTOLITE-L 3 | BYK | BENTOLITE-L 3 is a low iron rheology additive based on natural bentonite for aqueous plastic refractories. | |
| BYK-011 | BYK | BYK-011 is a silicone-free, polymer-based defoamer for aqueous coating systems (also radiation curable systems). It is particularly recommended for two pack polyurethane systems and offers very good recoatability. | |
| BYK®-012 | BYK | BYK®-012 is a compound of foam-destroying polymers and hydrophobic particles. This product is especially suitable for defoaming emulsion paints and plasters with a PVC-range of 30-85, where it prevents foam during production and application. The product i...view more BYK®-012 is a compound of foam-destroying polymers and hydrophobic particles. This product is especially suitable for defoaming emulsion paints and plasters with a PVC-range of 30-85, where it prevents foam during production and application. The product is silicone- and mineral oil-free and is specifically recommended for VOC-free systems. The additive shows optimum efficiency at low dosage, is acid and alkaline resistant and can be used in a pH-range of 3 - 12. The product may lead to turbidity and seeding in clear coats. view less | |
| BYK®-014 | BYK | BYK®-014 is a mixture of foam-destroying polymers, fat derivatives and hydrophobic particles. This product shows excellent defoaming properties in various emulsion types such as acrylates, styrene acrylics or VAE´s (vinyl acetate ethylene). It is especial...view more BYK®-014 is a mixture of foam-destroying polymers, fat derivatives and hydrophobic particles. This product shows excellent defoaming properties in various emulsion types such as acrylates, styrene acrylics or VAE´s (vinyl acetate ethylene). It is especially suitable for defoaming emulsion paints and plasters with a PVC range of 30-85. The product is silicone-free and mineral oil-free and is specifically recommended for VOC-free systems. The additive shows optimum efficiency at low dosage, is acid and alkaline resistant, and can be used in a pH range of 3 - 12. view less | |
| BYK-015 | BYK | BYK-015 is a silicone-free, polymer-based defoamer with anti-popping properties for aqueous coatings. Particularly recommended for automotive and industrial coatings. | |
| BYK®-016 | BYK | BYK®-016 is a compound of foam-destroying polymers and hydrophobic particles. It is a very effective silicone- and mineral oil free defoamer. It has no negative influence on the printing behavior and does not cause defects in the typography. At the time o...view more BYK®-016 is a compound of foam-destroying polymers and hydrophobic particles. It is a very effective silicone- and mineral oil free defoamer. It has no negative influence on the printing behavior and does not cause defects in the typography. At the time of publication the active compound in BYK-016 fully meets all requirements of the European Union for "materials and articles in contact with foodstuffs“, and complies with FDA 21 CFR § 175.105, 175.300, 175.320, 176.200, 176.210. view less | |
| BYK®-017 | BYK | BYK®-017 is a compound of foam destroying polysiloxanes and hydrophobic solids. It is especially suited for defoaming millbases during dispersion and subsequent processing. The product is an excellent defoamer for glycol pastes and aqueous pigment concent...view more BYK®-017 is a compound of foam destroying polysiloxanes and hydrophobic solids. It is especially suited for defoaming millbases during dispersion and subsequent processing. The product is an excellent defoamer for glycol pastes and aqueous pigment concentrates. It exhibits excellent defoaming during grinding and excellent storage stability. This results in improved grinding and handling of the final pigment concentrates and coatings. view less | |
| BYK®-018 | BYK | BYK®-018 is a mixture of hydrophobic solids and foam destroying polysiloxanes. It is especially suitable for pigmented emulsion systems based on styrene/ acrylate, acrylate or acrylate/polyurethane combinations with a low PVC. In industrial emulsion paint...view more BYK®-018 is a mixture of hydrophobic solids and foam destroying polysiloxanes. It is especially suitable for pigmented emulsion systems based on styrene/ acrylate, acrylate or acrylate/polyurethane combinations with a low PVC. In industrial emulsion paints that are applied by dipping, flow coating, and airless spraying BYK-018 is very efficient against microfoam. view less | |
| BYK®-019 | BYK | BYK®-019 is a solution of a polyether modified polydimethylsiloxane. BYK-019 is recommended for aqueous coatings based on polyurethane dispersions and polyurethane /acrylic combinations. It is also effective for defoaming pigment concentrate formulations....view more BYK®-019 is a solution of a polyether modified polydimethylsiloxane. BYK-019 is recommended for aqueous coatings based on polyurethane dispersions and polyurethane /acrylic combinations. It is also effective for defoaming pigment concentrate formulations. To reduce microfoam, a combination of BYK-019 with BYK-024 in a ratio of 3:2 has been shown to give excellent results. view less | |
| BYK®-021 | BYK | BYK®-021 is a mixture of foam destroying polysiloxanes and hydrophobic solids in polyglycol. It is particularly useful for pigmented emulsions based on styrene/acrylics, acrylics or acrylic/polyurethanes with PVC‘s of 18-25%. This defoamer has demonstrate...view more BYK®-021 is a mixture of foam destroying polysiloxanes and hydrophobic solids in polyglycol. It is particularly useful for pigmented emulsions based on styrene/acrylics, acrylics or acrylic/polyurethanes with PVC‘s of 18-25%. This defoamer has demonstrated high activity against microfoam in high gloss and semi-gloss aqueous coatings, specifically in airless and air-assisted spray applied coatings. view less | |
| BYK®-022 | BYK | BYK®-022 is a mixture of foam destroying polysiloxanes and hydrophobic solids in polyglycol. It is especially suited for pigmented emulsion systems based on styrene/acrylics, acrylics or acrylic/polyurethanes with PVC‘s of 18-25%. It can also be used in a...view more BYK®-022 is a mixture of foam destroying polysiloxanes and hydrophobic solids in polyglycol. It is especially suited for pigmented emulsion systems based on styrene/acrylics, acrylics or acrylic/polyurethanes with PVC‘s of 18-25%. It can also be used in amine-neutralized systems and is very efficient against microfoam. view less | |
| BYK®-023 | BYK | BYK®-023 is an emulsion of foam destroying polysiloxanes, hydrophobic solids and emulsifiers. This product is preferably used in pigmented emulsion paints with PVC‘s of 30-50% based on styrene/acrylics, acrylic or terpolymer binders. It also can be used i...view more BYK®-023 is an emulsion of foam destroying polysiloxanes, hydrophobic solids and emulsifiers. This product is preferably used in pigmented emulsion paints with PVC‘s of 30-50% based on styrene/acrylics, acrylic or terpolymer binders. It also can be used in hybrid systems. view less | |
| BYK®-024 | BYK | BYK®-024 is a mixture of foam destroying polysiloxanes and hydrophobic solids in polyglycol. This product is suited for emulsion systems with PVC‘s from 0 to 25% based on polyurethane and acrylic/polyurethane. It is especially useful in rolling, brushing ...view more BYK®-024 is a mixture of foam destroying polysiloxanes and hydrophobic solids in polyglycol. This product is suited for emulsion systems with PVC‘s from 0 to 25% based on polyurethane and acrylic/polyurethane. It is especially useful in rolling, brushing or spraying applications. view less | |
| BYK®-025 | BYK | BYK®-025 is a solution of foam destroying polysiloxanes. It is highly recommended for non-pigmented polyurethane and acrylic/ polyurethane emulsion systems. This defoamer is very easily incorporated and allows optimizing dosage by post-addition while the ...view more BYK®-025 is a solution of foam destroying polysiloxanes. It is highly recommended for non-pigmented polyurethane and acrylic/ polyurethane emulsion systems. This defoamer is very easily incorporated and allows optimizing dosage by post-addition while the paint is running on a curtain coater. view less | |
| BYK®-028 | BYK | BYK®-028 is a mixture of foam destroying polysiloxanes and hydrophobic solids in polyglycol. This product is the standard defoamer for water-based systems and the basis (starting selection) for the testing of a defoamer series. BYK-028 is suitable for dis...view more BYK®-028 is a mixture of foam destroying polysiloxanes and hydrophobic solids in polyglycol. This product is the standard defoamer for water-based systems and the basis (starting selection) for the testing of a defoamer series. BYK-028 is suitable for dispersion paints with a PVC from 0 to 25 based on acrylate/polyurethane or polyurethane. BYK-028 is easy to incorporate. view less | |
| BYK®-035 | BYK | BYK®-035 is a mixture of paraffin based mineral oils and hydrophobic components, containing silicone. This product is especially suitable for emulsion systems with a PVC of 20-40. Its effectiveness is not impaired by high shear forces. | |
| BYK®-037 | BYK | BYK®-037 is an emulsion of paraffin based mineral oils and hydrophobic components, containing silicone. It is used in all emulsion paints and plasters as well as for defoaming during the dispersion production. BYK-037 is very cost-efficient. | |
| BYK®-038 | BYK | BYK®-038 is a mixture of paraffin based mineral oils and hydrophobic components, containing silicone. This product is especially designed for universal use in APEO-free emulsions. It contains a small amount of a paint compatible silicone which enhances ex...view more BYK®-038 is a mixture of paraffin based mineral oils and hydrophobic components, containing silicone. This product is especially designed for universal use in APEO-free emulsions. It contains a small amount of a paint compatible silicone which enhances excellent efficiency. BYK-038 should be preferably used in emulsion systems with a PVC from 20 to 70. view less | |
| BYK-039 | BYK | BYK-039 is a mineral oil-based, VOC- and silicone-free defoamer for aqueous emulsion systems within a PVC range of 35-70. Does not contain alkylphenol ethoxylates. Also suitable for high-solid PUR leather coatings. | |
| BYK®-044 | BYK | BYK®-044 is an emulsion of hydrophobic particles and polysiloxanes. It is especially suitable for defoaming of the millbase during dispersion and further processing. The product defoams excellently glycol pastes and aqueous pigment concentrates. For defoa...view more BYK®-044 is an emulsion of hydrophobic particles and polysiloxanes. It is especially suitable for defoaming of the millbase during dispersion and further processing. The product defoams excellently glycol pastes and aqueous pigment concentrates. For defoaming of emulsion paints and dispersions lacquers BYK-044 is preferably used in pure acrylic and styrene acrylic emulsions. view less | |
| BYK®-054 | BYK | BYK®-054 is especially suited for solvent-free systems like PUR and epoxy floorings. It eliminates air-bubbles and ensures pinhole-free surfaces. Due to its strong incompatibility, the additive‘s influence on the transparency of clear systems must be eval...view more BYK®-054 is especially suited for solvent-free systems like PUR and epoxy floorings. It eliminates air-bubbles and ensures pinhole-free surfaces. Due to its strong incompatibility, the additive‘s influence on the transparency of clear systems must be evaluated. BYK-054 is also suitable to defoam plastisols. view less | |
| BYK®-055 | BYK | BYK®-055 is a solution of foam destroying polymers that is silicone free. This product is especially suitable for wood and furniture coatings based on glossy polyesters, paraffin-polyesters and UV-curing polyesters. Even at thin application parameters wit...view more BYK®-055 is a solution of foam destroying polymers that is silicone free. This product is especially suitable for wood and furniture coatings based on glossy polyesters, paraffin-polyesters and UV-curing polyesters. Even at thin application parameters with curtain coaters, curtain stability is provided. Used in non-pigmented wood coatings, a slight turbidity over dark wood could occur. Good results can also be achieved in epoxies. view less | |
| BYK®-057 | BYK | BYK®-057 is a solution of foam destroying polymers, silicone free. It is especially suitable for wood and furniture coatings based on glossy polyesters, paraffin-polyesters and UV-curing polyesters. Even at thin application parameters with curtain coaters...view more BYK®-057 is a solution of foam destroying polymers, silicone free. It is especially suitable for wood and furniture coatings based on glossy polyesters, paraffin-polyesters and UV-curing polyesters. Even at thin application parameters with curtain coaters, curtain stability is provided. Used in non-pigmented wood coatings, a slight turbidity over dark wood could occur. Good results can also be achieved in epoxies. view less | |
| BYK®-070 | BYK | BYK®-070 is a solution of foam destroying polymers and polysiloxanes. This product was developed for medium to high polar systems and is successfully used in the following resins: thermoplastic acrylics, chlorinated rubber, polyurethane, alkyd/urea, alkyd...view more BYK®-070 is a solution of foam destroying polymers and polysiloxanes. This product was developed for medium to high polar systems and is successfully used in the following resins: thermoplastic acrylics, chlorinated rubber, polyurethane, alkyd/urea, alkyd/melamine, and acrylic/melamine. Suggested application fields include machinery paints, radiator paints, industrial coatings, automotive systems and wood lacquers. view less | |
| BYK®-072 | BYK | BYK®-072 is a solution of foam destroying polysiloxanes. This product displays excellent defoaming activity in all solvent-borne systems. The active substance complies with FDA § 175.300 and is suitable for use in can coatings. This defoamer is very easy ...view more BYK®-072 is a solution of foam destroying polysiloxanes. This product displays excellent defoaming activity in all solvent-borne systems. The active substance complies with FDA § 175.300 and is suitable for use in can coatings. This defoamer is very easy to incorporate, allowing optimal dosage by post-addition. view less | |
| BYK®-077 | BYK | BYK®-077 is a solution of a polymethylalkylsiloxane. This product prevents foam and bubble formation arising during paint production and application in non-polar to high polar systems. It does not cause dewetting or defects in intercoat adhesion when reco...view more BYK®-077 is a solution of a polymethylalkylsiloxane. This product prevents foam and bubble formation arising during paint production and application in non-polar to high polar systems. It does not cause dewetting or defects in intercoat adhesion when recoated. view less | |
| BYK®-081 | BYK | BYK®-081 is a fluorine-free defoamer for solvent-borne and amine-neutralized systems. It is a highly effective and spontaneous defoamer. It can be used in amine-neutralized, water reducible coating systems and in solvent-borne coatings. It is particularly...view more BYK®-081 is a fluorine-free defoamer for solvent-borne and amine-neutralized systems. It is a highly effective and spontaneous defoamer. It can be used in amine-neutralized, water reducible coating systems and in solvent-borne coatings. It is particularly suitable for high solid alkyd systems in the architectural coatings sector. The additive shows good compatibility with clear coatings. BYK®-081 is not suitable for aqueous systems that contain little or no organic solvent as co-solvent. view less | |
| BYK®-085 | BYK | BYK®-085 is a polymethylalkylsiloxane. This product is the solvent-free version of BYK-077 and is used especially in systems in which solvent-free additives are requested or where a special solvent requirement exists. | |
| BYK®-088 | BYK | BYK®-088 is a solution of foam destroying polymers and polysiloxanes. This product displays excellent results in all solvent-borne and solvent-free systems (including aromaticfree formulations). The effective substance complies with FDA § 175.300 and is t...view more BYK®-088 is a solution of foam destroying polymers and polysiloxanes. This product displays excellent results in all solvent-borne and solvent-free systems (including aromaticfree formulations). The effective substance complies with FDA § 175.300 and is therefore especially appropriate for can coatings. Excellent performance is also demonstrated in the following systems: general industrial coatings, wood and furniture coatings and solvent-free UV-curing formulations. view less | |
| BYK®-092 | BYK | BYK®-092 is a VOC-free, silicone-containing defoamer for aqueous paint systems, printing inks and adhesives. Wide range of uses for conventional application methods | |
| BYK®-093 | BYK | BYK®-093 is a mixture of foam destroying polysiloxanes and hydrophobic solids in polyglycol. This product has a broad application profile. It is very compatible, and therefore exhibits a low tendency for surface defects (e. g. cratering, turbidity). This ...view more BYK®-093 is a mixture of foam destroying polysiloxanes and hydrophobic solids in polyglycol. This product has a broad application profile. It is very compatible, and therefore exhibits a low tendency for surface defects (e. g. cratering, turbidity). This additive combines a high efficiency with a broad compatibility in various coating systems. BYK-093 is highly suitable for clear and pigmented coatings, for all degrees of gloss and for all typical application methods. view less | |
| BYK®-094 | BYK | BYK®-094 is a compound of foam destroying polysiloxanes and hydrophobic solids. This product shows an excellent long-term efficiency, and it is as well suitable for flexo and gravure inks. BYK-094 is especially suitable for pigmented and non pigmented aqu...view more BYK®-094 is a compound of foam destroying polysiloxanes and hydrophobic solids. This product shows an excellent long-term efficiency, and it is as well suitable for flexo and gravure inks. BYK-094 is especially suitable for pigmented and non pigmented aqueous paints. It prevents foam during production and application of the paints. view less | |
| BYK®-141 | BYK | BYK®-141 is a solution of foam destroying polymers and polysiloxanes. This product is used in general industrial coatings, paper coatings, flooring systems and curtain coatings for wooden substrates. Preferred binders are oil-free polyesters, vinyls, poly...view more BYK®-141 is a solution of foam destroying polymers and polysiloxanes. This product is used in general industrial coatings, paper coatings, flooring systems and curtain coatings for wooden substrates. Preferred binders are oil-free polyesters, vinyls, polyurethane, epoxy esters, nitrocellulose, and acid-curing systems. view less | |
| BYK®-154 | BYK | BYK®-154 is a solution of an ammonium salt of an acrylate copolymer. This product increases gloss, reduces viscosity and provides good storage stability for the system. In combination with a wetting additive, such as DISPERBYK-181 (see data sheet W227) be...view more BYK®-154 is a solution of an ammonium salt of an acrylate copolymer. This product increases gloss, reduces viscosity and provides good storage stability for the system. In combination with a wetting additive, such as DISPERBYK-181 (see data sheet W227) better color acceptance of universal tinters is achieved. BYK-154 does not stabilize foam. view less | |
| BYK®-1610 | BYK | BYK®-1610 is an emulsion of hydrophobic solids, emulsifiers and foam destroying polysiloxanes. This product is recommended for use in emulsion paints with PVC‘s of 35 - 70. BYK-1610 also exhibits excellent efficiency in emulsion plasters. | |
| BYK-1611 | BYK | BYK-1611 is a VOC-free silicone-containing defoamer for aqueous coatings and adhesives. Preferably used in dispersion systems within a PVC range of 35-70. Cost-effective alternative to mineral oil defoamers. | |
| BYK®-1615 | BYK | BYK®-1615 is an emulsion of hydrophobic solids, emulsifiers and foam destroying polysiloxanes. This product is recommended for highly filled emulsion paints with PVC‘s of 60 - 85. | |
| BYK-1616 | BYK | BYK-1616 is a silicone-containing defoamer for aqueous printing inks and overprint varnishes, as well as aqueous wood and furniture coatings and general industrial coatings. | |
| BYK-1617 | BYK | BYK-1617 is a VOC-free silicone-containing defoamer for aqueous architectural coatings and adhesives. Preferably used in dispersion systems within a PVC range of 60-85. Cost-effective alternative to mineral oil defoamers. | |
| BYK®-1630 | BYK | BYK®-1630 is a VOC and APEO-free mineral oil defoamer for aqueous architectural coatings, general industrial coatings, floor coatings and adhesives. | |
| BYK®-1640 | BYK | BYK®-1640 is a polymer-based, VOC- and silicone-free defoamer for aqueous coatings, printing inks, adhesives, paper coatings, and construction chemicals. It offers optimum performance at the lowest dosage. This product is also suitable for applications th...view more BYK®-1640 is a polymer-based, VOC- and silicone-free defoamer for aqueous coatings, printing inks, adhesives, paper coatings, and construction chemicals. It offers optimum performance at the lowest dosage. This product is also suitable for applications that come into contact with food. view less | |
| BYK-1641 | BYK | BYK-1641 is a VOC- and mineral oil-free defoamer for aqueous systems that is very easy to incorporate and has an excellent price-performance ratio. | |
| BYK-1642 | BYK | BYK-1642 is a polymer-based, VOC- and silicone-free defoamer for aqueous coatings, printing inks, adhesives, paper coatings, and construction chemicals. Optimum performance at the lowest dosage. | |
| BYK®-1650 | BYK | BYK®-1650 is an emulsion of siloxylated polyethers and hydrophobic particles. This product is suitable for emulsion paints with PVC‘s of 35 - 70. The defoamer shows excellent long term efficiency and has no negative influence on color acceptance. | |
| BYK-1679 | BYK | BYK-1679 is a silicone defoamer on the basis of an emulsion for aqueous textile coatings. It is a very easy to incorporate defoamer for aqueous adhesive systems. The additive is extremely well suited to being incorporated without high shear forces in very...view more BYK-1679 is a silicone defoamer on the basis of an emulsion for aqueous textile coatings. It is a very easy to incorporate defoamer for aqueous adhesive systems. The additive is extremely well suited to being incorporated without high shear forces in very low viscosity systems. It is particularly suitable for defoaming primary PE emulsions (e.g. HORDAMER types). BYK-1679 is a suitable defoamer for use in the cooling water circuit when performing the underwater granulation of hot melt adhesives where HORDAMER is being used as an anti-blocking additive. view less | |
| BYK®-1680 | BYK | BYK®-1680 is a VOC-free, liquid defoamer for aqueous construction material applications, in particular in combination with concrete admixtures based on polycarboxylate ethers. | |
| BYK®-1707 | BYK | BYK®-1707 is a silicone-containing defoamer for aqueous pigment concentrates and glycol pastes for use in printing inks and coatings. Prevents foam during grinding. Long-term stability. Particularly suitable for grinds that contain resins. | |
| BYK®-1709 | BYK | BYK®-1709 is a silicone-containing defoamer for aqueous pigment concentrates for use in coatings, printing inks and overprint varnishes. Prevents foam during grinding. Long-term and shear stability. Particularly suited to resin-free grinds (slurries). | |
| BYK®-1710 | BYK | BYK®-1710 is a mixture of foam destroying polymers and hydrophobic solids This product has excellent defoaming properties, especially in alkyd emulsion paints, hybrids, PU, and EP coatings. |
