| ACRIBEN RF 450 | Benasedo | ACRIBEN RF 450 is a low hydroxyl content binder suitable to be crosslinked both with aliphatic and aromatic isocyanates, when producing enamels for metals or for plastic substrates, to be cured at room temperature or in the oven. | Request Sample |
| ACRIBEN SA 338 | Benasedo | ACRIBEN SA 338 is a self crosslinking acrylic polymer endowed with very good transparency, good chemical resistance, and non-yellowing properties. It is suitable to formulate fast drying clear and pigmented water based top-coats for furniture. | Request Sample |
| ACRIBEN SA 437 | Benasedo | ACRIBEN SA 437 is a self crosslinking acrylic polymer. It is suitable to formulate fast drying clear and pigmented water based sealers for furniture. | Request Sample |
| ACRIBEN SA 5302 | Benasedo | ACRIBEN SA 5302 is a self crosslinking acrylic polymer endowed with high blocking resistance, good early water resistance, good alkaline resistance, very good transparency, and non yellowing properties. It is suitable to formulate clear and pigmented fast...view more ACRIBEN SA 5302 is a self crosslinking acrylic polymer endowed with high blocking resistance, good early water resistance, good alkaline resistance, very good transparency, and non yellowing properties. It is suitable to formulate clear and pigmented fast drying and fast blocking resistant coatings for Joinery, suitable both for interior and exterior applications. view less | Request Sample |
| ANTI-TERRA®-203 | BYK | ANTI-TERRA®-203 is a solution of an alkylammonium salt of a polycarboxylic acid. This product is suitable for medium to low polar solvent-borne and solvent-free coating systems. It causes an increase in thixotropy. In highly filled systems, the sagging te...view more ANTI-TERRA®-203 is a solution of an alkylammonium salt of a polycarboxylic acid. This product is suitable for medium to low polar solvent-borne and solvent-free coating systems. It causes an increase in thixotropy. In highly filled systems, the sagging tendency is reduced; in addition, no negative influence on the water sensitivity of the paint film has been observed. When formulated into anti-corrosion primers, the protective properties are enhanced in many instances. view less | |
| ANTI-TERRA®-204 | BYK | ANTI-TERRA®-204 is a solution of a polycarboxylic acid salt of polyamine amides. In comparison to ANTI-TERRA-203, ANTI-TERRA-204 can additionally be used in non-polar systems and is compatible with white spirits. The lower the polarity the more the thixot...view more ANTI-TERRA®-204 is a solution of a polycarboxylic acid salt of polyamine amides. In comparison to ANTI-TERRA-203, ANTI-TERRA-204 can additionally be used in non-polar systems and is compatible with white spirits. The lower the polarity the more the thixotropy is increased. The preferred binders are long, medium and short oil alkyds, PVC-copolymers, chlorinated rubber and epoxy. Even in "low-filled“ systems, the sagging tendency is reduced; in addition, no negative influence on the water sensitivity of the paint film has been observed. When formulated into anticorrosion primers, the protective properties are enhanced in many instances. view less | |
| ANTI-TERRA®-205 | BYK | ANTI-TERRA®-205 is a high molecular weight wetting and dispersing additives for solvent-borne systems. Solution of a polycarboxylic acid salt of polyamine amides. | |
| ANTI-TERRA®-250 | BYK | ANTI-TERRA®-250 is a solution of an alkylolammonium salt of a high molecular weight acidic polymer. It is used in aqueous systems and provides an increase in thixotropy and prevents hard settling of pigments. Due to controlled flocculation mechanism, the ...view more ANTI-TERRA®-250 is a solution of an alkylolammonium salt of a high molecular weight acidic polymer. It is used in aqueous systems and provides an increase in thixotropy and prevents hard settling of pigments. Due to controlled flocculation mechanism, the use of ANTI-TERRA-250 may lead to a minor gloss reduction. view less | |
| ANTI-TERRA®-U | BYK | ANTI-TERRA-U is the standard wetting and dispersing additive for solvent-borne industrial and architectural coatings. It can also be utilized to provide excellent gelling in organo-philic bentonites. This product is composed of a solution of a salt of uns...view more ANTI-TERRA-U is the standard wetting and dispersing additive for solvent-borne industrial and architectural coatings. It can also be utilized to provide excellent gelling in organo-philic bentonites. This product is composed of a solution of a salt of unsaturated polyamine amides and lower molecular weight acidic polyesters. view less | |
| ANTI-TERRA®-U 100 | BYK | ANTI-TERRA-U 100 is the solvent-free version of ANTI-TERRA U , the standard wetting and dispersing additive for solvent-borne industrial and architectural coatings. It can also be used to provide excellent gelation of organophilic bentonites. ANTI-TERR...view more ANTI-TERRA-U 100 is the solvent-free version of ANTI-TERRA U , the standard wetting and dispersing additive for solvent-borne industrial and architectural coatings. It can also be used to provide excellent gelation of organophilic bentonites. ANTI-TERRA-U 100 is effective for wetting and dispersing colored pigments, both organic and inorganic. No adverse effect has been observed on the pot-life of two-component systems or on the dry time of oxidative cure binders. ANTI-TERRA-U 100 can also be used as a wetting and suspending additive in water soluble coatings. view less | |
| AQUACER 1013 | BYK | AQUACER 1013 is a VOC-free HDPE-based wax emulsion for improving the surface protection in aqueous coatings and printing inks as well as in aqueous care products and polishes. | |
| AQUACER 1031 | BYK | AQUACER 1031 is an emulsion based on a polyethylene wax for improving the surface properties of aqueous care products. It offers an anti-slip effect and good foot traffic resistance. | |
| AQUACER 1039 | BYK | AQUACER 1039 is a paraffin wax emulsion for improved surface characteristics in aqueous coatings and printing inks. | |
| AQUACER 1040 | BYK | AQUACER 1040 is a primary polyethylene dispersion for formulating release agents for metal die casting. | |
| AQUACER 1061 | BYK | AQUACER 1061 is an emulsion of an ethylene-acrylic acid copolymer wax for improving the surface characteristics of paper. | |
| AQUACER 1063 | BYK | AQUACER 1063 is a polyethylene dispersion to improve the anti-caking properties of hot-melt adhesives and to increase adhesion in dispersion adhesives for the packaging sector. | |
| AQUACER 1075 | BYK | AQUACER 1075 is an emulsion based on an HD polyethylene wax to improve the surface properties of aqueous care products and polishes, and aqueous printing inks. | |
| AQUACER 1510 | BYK | AQUACER 1510 is a polypropylene wax emulsion for aqueous glass fiber sizings to improve the mechanical properties in glass fiber- reinforced PP compounds. | |
| AQUACER® 1547 | BYK | AQUACER® 1547 is a wax emulsion for improving surface properties of water-borne can coatings. It is an anionic emulsion of an oxidized HD polyethylene wax. This product improves scratch resistance. | |
| AQUACER 2500 | BYK | AQUACER 2500 is a wax emulsion on the basis of modified PE for aqueous foil and paper coatings to improve slip and abrasion resistance. | |
| AQUACER 2650 | BYK | AQUACER 2650 is a wax emulsion based on carnauba wax for aqueous thermal transfer systems, car care products and aqueous leather coatings. It seals and thereby covers any minor scratches on the surface that is to be treated and restores the color of the s...view more AQUACER 2650 is a wax emulsion based on carnauba wax for aqueous thermal transfer systems, car care products and aqueous leather coatings. It seals and thereby covers any minor scratches on the surface that is to be treated and restores the color of the surface. The melting point of 85 °C means that the wax emulsion can easily be polished up using a soft terry cloth or microfiber cloth, but polishing with mechanical tools is also possible. view less | |
| AQUACER 3500 | BYK | AQUACER 3500 is a cationic wax emulsion based on a modified polypropylene wax for formulating release agents for metal die casting. | |
| AQUACER 494 | BYK | AQUACER 494 is an aqueous paraffin wax emulsion for care products and polishes. | |
| AQUACER 497 | BYK | AQUACER 497 is a paraffin-based wax emulsion for aqueous coatings, printing inks as well as care products and polishes for improving water repellency and surface slip. | |
| AQUACER 501 | BYK | AQUACER 501 is an HDPE-based wax emulsion for aqueous systems to improve surface protection. | |
| AQUACER 506 | BYK | AQUACER 506 is an emulsion based on a HD polyethylene wax for improving the surface properties of aqueous care products and polishes. It improves the buffability, increases filling capacity and produces an anti-slip effect. The above-mentioned properties ...view more AQUACER 506 is an emulsion based on a HD polyethylene wax for improving the surface properties of aqueous care products and polishes. It improves the buffability, increases filling capacity and produces an anti-slip effect. The above-mentioned properties are generated by mixing AQUACER 506 with polymers in a ratio of 3:1 (solid wax to solid polymer). A mixing ratio of 1:6 increases the water- and alcohol-resistance, the protection against heel marks (= foot traffic resistance), and the dirt-repellent action. AQUACER 506 is compatible with all known polymer dispersions and plasticizers. view less | |
| AQUACER® 507 | BYK | AQUACER® 507 is an anionic emulsion of an oxidized HD polyethylene wax. It is suitable for use in non-ionic and anionic water-borne automotive systems and industrial paints. This product enhances flip-flop effect, improves the D.O.I. of clear coats, enhan...view more AQUACER® 507 is an anionic emulsion of an oxidized HD polyethylene wax. It is suitable for use in non-ionic and anionic water-borne automotive systems and industrial paints. This product enhances flip-flop effect, improves the D.O.I. of clear coats, enhances hardness and slip, and reduces short wave defects (mottling, Bénard cells). view less | |
| AQUACER® 513 | BYK | AQUACER® 513 is a non-ionic emulsion based on an oxidized HD polyethylene wax. It is suitable for use in aqueous systems and printing inks. This product improves the following surface properties: scratch resistance in aqueous systems, rub resistance in pr...view more AQUACER® 513 is a non-ionic emulsion based on an oxidized HD polyethylene wax. It is suitable for use in aqueous systems and printing inks. This product improves the following surface properties: scratch resistance in aqueous systems, rub resistance in printing inks and black heel marking resistance in parquet lacquers. view less | |
| AQUACER 519 | BYK | AQUACER 519 is an emulsion based on a HD polyethylene wax for improving the surface properties of aqueous care products and polishes. It improves the buffability, increases filling capacity and produces an anti-slip effect. The above-mentioned properties ...view more AQUACER 519 is an emulsion based on a HD polyethylene wax for improving the surface properties of aqueous care products and polishes. It improves the buffability, increases filling capacity and produces an anti-slip effect. The above-mentioned properties are generated by mixing AQUACER 519 with polymers in a ratio of 3:1 (solid wax to solid polymer). A mixing ratio of 1:6 increases the water- and alcohol-resistance, the protection against heel marks (= foot traffic resistance), and the dirt-repellent action. AQUACER 519 is compatible with all known polymer dispersions and plasticizers. view less | |
| AQUACER® 526 | BYK | AQUACER® 526 is a wax emulsion for water-borne effect coatings. It is an emulsion of an anionic modified Ethylene-Vinyl Acetate-Copolymer wax (EVA). This product is suitable for water-borne top coats and base coats. It enhances flip-flop effect, improves ...view more AQUACER® 526 is a wax emulsion for water-borne effect coatings. It is an emulsion of an anionic modified Ethylene-Vinyl Acetate-Copolymer wax (EVA). This product is suitable for water-borne top coats and base coats. It enhances flip-flop effect, improves orientation of effect pigments (aluminum, mica, etc.), reduces short wave defects (mottling, Bénard cells), and there is no negative influence on chemical resistance. view less | |
| AQUACER 527 | BYK | AQUACER 527 is a wax emulsion based on a modified EVA copolymer wax to improve surface characteristics in aqueous coating systems and printing inks. | |
| AQUACER 528 | BYK | AQUACER 528 is an emulsion based on an ethylene-acrylic acid-copolymer wax for improving the surface properties of aqueous care products. It offers strong anti-slip effect and good foot traffic resistance. | |
| AQUACER 530 | BYK | AQUACER 530 is a wax emulsion for improved surface characteristics in aqueous printing inks, overprint varnishes, wood and furniture coatings as well as inkjet inks. | |
| AQUACER® 531 | BYK | AQUACER® 531is a wax emulsion for improving surface properties of water-borne industrial paints and printing inks. It is a non-ionic emulsion based on a modified polyethylene wax. This additive improves the following surface properties: slip, scratch resi...view more AQUACER® 531is a wax emulsion for improving surface properties of water-borne industrial paints and printing inks. It is a non-ionic emulsion based on a modified polyethylene wax. This additive improves the following surface properties: slip, scratch resistance, rub resistance and anti blocking. view less | |
| AQUACER 532 | BYK | AQUACER 532 is an emulsion of a modified HD polyethylene wax for improved surface characteristics in aqueous coating systems. | |
| AQUACER® 533 | BYK | AQUACER® 533 is a wax emulsion on the basis of modified paraffin for aqueous systems to improve surface slip, anti-blocking, and water-resistance. It is typically used in architectural coatings and in the printing inks industry. | |
| AQUACER® 537 | BYK | AQUACER® 537 is an anionic emulsion based on a modified paraffin wax. It is suitable for aqueous systems for furniture- and parquet, industrial- and decorative paints. This product improves the following surface properties: water repellency, anti blocking...view more AQUACER® 537 is an anionic emulsion based on a modified paraffin wax. It is suitable for aqueous systems for furniture- and parquet, industrial- and decorative paints. This product improves the following surface properties: water repellency, anti blocking and slip. view less | |
| AQUACER® 539 | BYK | AQUACER® 539 is a non-ionic emulsion based on a modified paraffin wax. This product is suitable for aqueous systems for furniture- and parquet, industrial- and decorative paints. It improves the following surface properties: slip, water repellency, anti b...view more AQUACER® 539 is a non-ionic emulsion based on a modified paraffin wax. This product is suitable for aqueous systems for furniture- and parquet, industrial- and decorative paints. It improves the following surface properties: slip, water repellency, anti blocking, scratch resistance, rub resistance and soft feel effect. view less | |
| AQUACER 541 | BYK | AQUACER 541 is an aqueous emulsion of a montan ester wax for care products and polishes as well as for aqueous coating systems and leather coatings. | |
| AQUACER® 552 | BYK | AQUACER® 552 is a non-ionic emulsion based on an oxidized HD polyethylene wax. This product is suitable for use in aqueous systems and printing inks. It is used to improve scratch resistance in aqueous systems. | |
| AQUACER 561 | BYK | AQUACER 561 is a beeswax-based wax emulsion to improve surface protection in aqueous care products and coating systems. | |
| AQUACER 565 | BYK | AQUACER 565 is an aqueous carnauba wax emulsion for improving the surface characteristics of care products, polishes, and leather coatings. It seals and thereby covers any minor scratches on the surface that is to be treated and restores the color of the ...view more AQUACER 565 is an aqueous carnauba wax emulsion for improving the surface characteristics of care products, polishes, and leather coatings. It seals and thereby covers any minor scratches on the surface that is to be treated and restores the color of the surface. The melting point of 85 °C means that the wax emulsion can easily be polished up using a soft terry cloth or microfiber cloth, but polishing with mechanical tools is also possible. view less | |
| AQUACER 570 | BYK | AQUACER 570 is a modified Ecolabel-compliant sunflower wax emulsion to improve the surface properties of care products and polishes. It seals and thereby covers any minor scratches on the surface that is to be treated, and restores the surface’s original ...view more AQUACER 570 is a modified Ecolabel-compliant sunflower wax emulsion to improve the surface properties of care products and polishes. It seals and thereby covers any minor scratches on the surface that is to be treated, and restores the surface’s original color. It also improves the hydrophobicity and the oleophobicity of care products and polishes. This product is recommended for maintaining and protecting all types of surfaces, for leather, coated and uncoated surfaces. view less | |
| AQUACER 571 | BYK | AQUACER 571 is a modified rice bran wax emulsion to improve the surface properties of care products, polishes, and aqueous coating systems. | |
| AQUACER 581 | BYK | AQUACER 581 is a wax emulsion based on carnauba wax for aqueous paper coatings to improve surface slip, scratch-resistance, uniformity of printing ink acceptance, and ink setoff. Anti-caking additive for thermoplastics and hotmelts. | |
| AQUACER 582 | BYK | AQUACER 582 is an emulsion based on a polyethylene wax for improving the surface properties of aqueous seed coatings. | |
| AQUACER 583 | BYK | AQUACER 583 is a wax emulsion used to improve the surface characteristics of seed coatings. | |
| AQUACER® 593 | BYK | AQUACER® 593 is a wax emulsion for improving anti slip of water-borne paint systems and printing inks. It is a non-ionic emulsion of a modified polypropylene wax. This product is suitable for use in non-ionic and anionic water-borne paint systems and prin...view more AQUACER® 593 is a wax emulsion for improving anti slip of water-borne paint systems and printing inks. It is a non-ionic emulsion of a modified polypropylene wax. This product is suitable for use in non-ionic and anionic water-borne paint systems and printing inks. view less | |
| AQUACER 595 | BYK | AQUACER 595 is an emulsion based on a modified polypropylene wax for improving the surface properties of aqueous care products. It offers a strong anti-slip effect and good dirt repulsion. In aqueous leather finishes it produces an anti-slip and anti-tack...view more AQUACER 595 is an emulsion based on a modified polypropylene wax for improving the surface properties of aqueous care products. It offers a strong anti-slip effect and good dirt repulsion. In aqueous leather finishes it produces an anti-slip and anti-tack effect. view less | |
| AQUACER 597 | BYK | AQUACER 597 is a cationic wax emulsion based on a modified polypropylene wax for formulating release agents for metal die casting. | |
| AQUACER® 840 | BYK | AQUACER® 840 is a cationic emulsion of an oxidized HD polyethylene wax. This product is suitable for use in non-ionic and anionic water-borne automotive systems and industrial paints. It enhances flip-flop effect, improves the D.O.I. of clear coats, impro...view more AQUACER® 840 is a cationic emulsion of an oxidized HD polyethylene wax. This product is suitable for use in non-ionic and anionic water-borne automotive systems and industrial paints. It enhances flip-flop effect, improves the D.O.I. of clear coats, improves orientation of effect pigments and reduces short wave defects. view less | |
| AQUAMAT® 208 | BYK | AQUAMAT® 208 is an oxidized HD polyethylene wax dispersion. It is suitable for aqueous systems e. g. furniture- and parquet lacquer, industrial- and decorative paints and inks. The additive improves the following surface properties: gloss reduction, scrat...view more AQUAMAT® 208 is an oxidized HD polyethylene wax dispersion. It is suitable for aqueous systems e. g. furniture- and parquet lacquer, industrial- and decorative paints and inks. The additive improves the following surface properties: gloss reduction, scratch resistance and soft feel effect. view less | |
| AQUAMAT® 263 | BYK | AQUAMAT® 263 is an oxidized HD polyethylene wax dispersion. This product is suitable for aqueous systems e. g. furniture- and parquet lacquer, industrial- and decorative paints and inks. The additive improves the following surface properties: gloss reduct...view more AQUAMAT® 263 is an oxidized HD polyethylene wax dispersion. This product is suitable for aqueous systems e. g. furniture- and parquet lacquer, industrial- and decorative paints and inks. The additive improves the following surface properties: gloss reduction, scratch resistance, soft feel effect, rub resistance, anti blocking and black heel resistance. view less | |
| AQUATIX® 8421 | BYK | AQUATIX® 8421 is a non-ionic emulsion of a modified Ethylene-Vinyl-Acetate (EVA) copolymer wax. It improves the rheological properties and brilliance of effect pigment slurries that are co-solvent-free. This product provides the following properties: impr...view more AQUATIX® 8421 is a non-ionic emulsion of a modified Ethylene-Vinyl-Acetate (EVA) copolymer wax. It improves the rheological properties and brilliance of effect pigment slurries that are co-solvent-free. This product provides the following properties: improves effect pigment orientation, reduces cloudiness /mottling, shows less sensivity to co-solvents in coating systems compared to PU based thickeners, is “ready to use”, provides easy handling and incorporation compared to clays or acrylic thickeners, and excellent anti-settling properties in coatings during storage and application. view less | |
| BENALAC 5660 | Benasedo | BENALAC 5660 is an air-dryng long-oil alkyd resin specially designed for “off-set inks”. It is endowed with good setting and drying characteristics, excellent wetting power, colour development and scuff resistance, flow and non- yellowing properties. | Request Sample |
| BENALAC UR 81 | Benasedo | BENALAC UR 81 is a solventless aromatic urethane modified oil endowed with fast air drying properties, hardness and gloss. It finds applications as a vehicle in “off set“ inks by reducing the tack-free time and improving levelling and rub test resistance....view more BENALAC UR 81 is a solventless aromatic urethane modified oil endowed with fast air drying properties, hardness and gloss. It finds applications as a vehicle in “off set“ inks by reducing the tack-free time and improving levelling and rub test resistance. Due to its excellent pigments wetting properties is particularly suitable as grinding vehicle. It is also suitable for interior and exterior clear varnishes and for wood stains in compliance with CE 2004 – 42 requirements for the VOC reduction. view less | Request Sample |
| Benasol 1804 | Benasedo | Benasol 1804 is a Linseed - Tung Phenolic oil, with a 68% oil content. It contains 70% solids, Z1-Z2 visc. [G.H], 6-12 A.V. solids, and a 9 color [G.H.] max. It is used in anticorrosive primers, enamels and clear finishes with excellent resistance to mari...view more Benasol 1804 is a Linseed - Tung Phenolic oil, with a 68% oil content. It contains 70% solids, Z1-Z2 visc. [G.H], 6-12 A.V. solids, and a 9 color [G.H.] max. It is used in anticorrosive primers, enamels and clear finishes with excellent resistance to marine corrosion. view less | Request Sample |
| BENASOL 4377 | Benasedo | BENASOL 4377 is a low viscosity, plasticizing, non yellowing alkyd resin suitable to produce nitrocellulose wood lacquers, endowed with very fast solvent release, high build-up flow, gloss and lifting resistance. | Request Sample |
| Benasol 4V | Benasedo | Benasol 4V is a very fast air drying alkyd resin phenolic modified having good through dry. It is especially recommended for rust-inhibitive metal and nitrocellulose non lifting primers, fast air–drying enamels for farm and industrial equipment. | Request Sample |
| Benasol 5097 in White Spirit | Benasedo | Benasol 5097 in White Spirit is used in quick air-drying primers and enamels with excellent chemical and outdoor resistance. It is made from Linseed - Tung Phenolic oil and has an oil content of 42%. This product contains 50% solids, a viscosity [G.H.] of...view more Benasol 5097 in White Spirit is used in quick air-drying primers and enamels with excellent chemical and outdoor resistance. It is made from Linseed - Tung Phenolic oil and has an oil content of 42%. This product contains 50% solids, a viscosity [G.H.] of X-Z, an A.V. solids amount of 6-15, and a color [G.H] max. of 9. Its application is for air. view less | Request Sample |
| Benasol 5097 in Xylene | Benasedo | Benasol 5097 in Xylene is used in quick air-drying primers and enamels with excellent chemical and outdoor resistance. This product has an oil content of 42%, a solids amount of 50%, an A.V. solids amount of 6-15, and a viscosity [G.H.] of U-W. Its applic...view more Benasol 5097 in Xylene is used in quick air-drying primers and enamels with excellent chemical and outdoor resistance. This product has an oil content of 42%, a solids amount of 50%, an A.V. solids amount of 6-15, and a viscosity [G.H.] of U-W. Its application is for air. view less | Request Sample |
| BENASOL A 240 | Benasedo | BENASOL A 240 is a very fast curing binder suitable for two pack wood lacquers, sealers and top coats, where it shows good sandability hardness and filling properties. It has excellent lifting resistance and good compatibility with nitrocellulose. | Request Sample |
| Benasol AS 280 | Benasedo | Benasol AS 280 is used in fast air-drying and low-bake enamels with excellent chemical resistance. It is made from soya oil and has a 28% oil content. It contains 60% solids, has a viscosity [G.H.] of Y-Z1, an A.V. solids amount of 6-15, and a colour [G.H...view more Benasol AS 280 is used in fast air-drying and low-bake enamels with excellent chemical resistance. It is made from soya oil and has a 28% oil content. It contains 60% solids, has a viscosity [G.H.] of Y-Z1, an A.V. solids amount of 6-15, and a colour [G.H.] maximum of 5. This product has applications for air, bake, nitro and catalyze. view less | Request Sample |
| BENASOL AS 308 in XYLENE | Benasedo | BENASOL AS 308 in XYLENE is a medium-oil non–yellowing alkyd resin having fast trough drying, good gloss, hardness, adhesion and outdoor resistance. It is suitable to produce enamels for building and industrial applications, also in combination with chlor...view more BENASOL AS 308 in XYLENE is a medium-oil non–yellowing alkyd resin having fast trough drying, good gloss, hardness, adhesion and outdoor resistance. It is suitable to produce enamels for building and industrial applications, also in combination with chlorinated rubber, for farm machinery enamels, when sudden outdoor exposure is required. view less | Request Sample |
| BENASOL AS 308 in XYLENE /WHITE SPIRIT (30/15) | Benasedo | BENASOL AS 308 in XYLENE /WHITE SPIRIT (30/15) is a medium-oil non–yellowing alkyd resin having fast trough drying, good gloss, hardness, adhesion and outdoor resistance. It is suitable to produce enamels for building and industrial applications, also in ...view more BENASOL AS 308 in XYLENE /WHITE SPIRIT (30/15) is a medium-oil non–yellowing alkyd resin having fast trough drying, good gloss, hardness, adhesion and outdoor resistance. It is suitable to produce enamels for building and industrial applications, also in combination with chlorinated rubber, for farm machinery enamels, when sudden outdoor exposure is required. view less | Request Sample |
| BENASOL AS 3716 | Benasedo | BENASOL AS 3716 is a non–yellowing alkyd resin having fast trough drying, good gloss, hardness, adhesion and outdoor resistance. It is suitable to produce high-solids enamels for building and industrial applications, also combining with chlorinated rubber...view more BENASOL AS 3716 is a non–yellowing alkyd resin having fast trough drying, good gloss, hardness, adhesion and outdoor resistance. It is suitable to produce high-solids enamels for building and industrial applications, also combining with chlorinated rubber, for farm machinery enamels, when sudden outdoor exposure is required. view less | Request Sample |
| Benasol AS 379 | Benasedo | Benasol AS 379 is used in fast air-drying white and coloured enamels for industrial applications. It is made from special fatty acids with 43% oil content and 60% solids content. This product has a viscosity [G.H.] of Z1-Z2, an A.V. solids amount of 6-12,...view more Benasol AS 379 is used in fast air-drying white and coloured enamels for industrial applications. It is made from special fatty acids with 43% oil content and 60% solids content. This product has a viscosity [G.H.] of Z1-Z2, an A.V. solids amount of 6-12, and a color [G.H.] maximum of 5. It has application for air. view less | Request Sample |
| BENASOL AS 452 | Benasedo | BENASOL AS 452 is an air-drying low-viscosity, non-yellowing alkyd resin especially modified so to guarantee very good wetting properties with pigments, fillers and wide compatibility with various binder types used in different formulations. | Request Sample |
| BENASOL AS 453 | Benasedo | BENASOL AS 453 is an air-drying low-viscosity, non-yellowing alkyd resin especially modified so to guarantee very good wetting properties with pigments, fillers and wide compatibility with various binder types used in different formulations. | Request Sample |
| Benasol B1 | Benasedo | Benasol B1 is used in urethane two-component mat finishes and sealers with high reactivity and easy sandability, and it has nitro and catalyze applications. This product contains vegetable fatty acids, with 30% oil content and a 50% solids amount. It has ...view more Benasol B1 is used in urethane two-component mat finishes and sealers with high reactivity and easy sandability, and it has nitro and catalyze applications. This product contains vegetable fatty acids, with 30% oil content and a 50% solids amount. It has a viscosity [G.H.] of X-Y, an A.V. solids amount of 6-15, a color [G.H.] max. of 5, and an OH solids of 2.6-2.8%. view less | Request Sample |
| Benasol C 300 | Benasedo | Benasol C 300 is used in non-yellowing baking enamels, polyurethane finishes and nitrocellulose lacquers. It contains coconut fatty acids, with a 33% oil content. This product has a 60% solids content, a viscosity [G.H.] of Z1-Z2, an A.V. solids amount of...view more Benasol C 300 is used in non-yellowing baking enamels, polyurethane finishes and nitrocellulose lacquers. It contains coconut fatty acids, with a 33% oil content. This product has a 60% solids content, a viscosity [G.H.] of Z1-Z2, an A.V. solids amount of 6-15, and an OH solids of 2.8-3.0%. Benasol C 300 has bake, nitro and catalyze applications. view less | Request Sample |
| BENASOL CO 34 | Benasedo | BENASOL CO 34 is an alkyd resin with a particular molecular structure,endowed with very fast drying properties, good performances in adhesion,hardness and through-dry. It is suggested to formulate industrial sealer and finishes, i.e. machinery,aerosol ena...view more BENASOL CO 34 is an alkyd resin with a particular molecular structure,endowed with very fast drying properties, good performances in adhesion,hardness and through-dry. It is suggested to formulate industrial sealer and finishes, i.e. machinery,aerosol enamels,traffic-paints. view less | Request Sample |
| Benasol CO 35 in Xylene | Benasedo | Benasol CO 35 in Xylene is used in very fast air-drying enamels for industrial applications and traffic-paints. It is made using soya fatty acids, with a 44% oil content. It has a viscosity [G.H.] of Z2-Z4, a 60% solids amount, an A.V. solids content of 6...view more Benasol CO 35 in Xylene is used in very fast air-drying enamels for industrial applications and traffic-paints. It is made using soya fatty acids, with a 44% oil content. It has a viscosity [G.H.] of Z2-Z4, a 60% solids amount, an A.V. solids content of 6-15, and a colour [G.H.] of maximum 8. This product has air applications. view less | Request Sample |
| Benasol CO 35 in Xylene/Butylacetate | Benasedo | Benasol CO 35 in Xylene/Butylacetate is used in very fast air-drying enamels for industrial applications and traffic-paints, and also has air applications. It is made using soya fatty acids, with a 44% oil content. It has a viscosity [G.H.] of Z2-Z3, a 65...view more Benasol CO 35 in Xylene/Butylacetate is used in very fast air-drying enamels for industrial applications and traffic-paints, and also has air applications. It is made using soya fatty acids, with a 44% oil content. It has a viscosity [G.H.] of Z2-Z3, a 65% solids amount, an A.V. solids content of 6-15, and a colour [G.H.] of maximum 4. view less | Request Sample |
| Benasol CO 37 in BUTYL ACETATE | Benasedo | Benasol CO 37 in BUTYL ACETATE is used in very fast non-yellowing air-drying enamels for exterior applications, particularly farm equipment. It is made using special fatty acids and Urethane Aliphatic, and has a 37% oil content. This product contains 65% ...view more Benasol CO 37 in BUTYL ACETATE is used in very fast non-yellowing air-drying enamels for exterior applications, particularly farm equipment. It is made using special fatty acids and Urethane Aliphatic, and has a 37% oil content. This product contains 65% solids, a viscosity [G.H.] of Z1-Z2, an A.V. solids content of 5-12, and a color [G.H.] maximum of 4. This product has air applications. view less | Request Sample |
| Benasol E 114 | Benasedo | Benasol E 114 is used in clear and pigmented finishes for metals and wood. It has a large compatibility with acrylics, polyesters, alkyds, film-forming vehicles and universal tinting-systems. It contains synthetic fatty acids, with a 25% oil amount. This ...view more Benasol E 114 is used in clear and pigmented finishes for metals and wood. It has a large compatibility with acrylics, polyesters, alkyds, film-forming vehicles and universal tinting-systems. It contains synthetic fatty acids, with a 25% oil amount. This product has a viscosity [G.H.] of Z3-Z5, a colour max. of 3, an OH solids amount of 5.4-5.6, and solids amount of 75%. Benasol E 114 has bake, nitro, and catalyze applications. view less | Request Sample |
| Benasol E 184 | Benasedo | Benasol E 184 is made using synthetic fatty acids, with an oil content of 28% and a solids amount of 70%. This product has a viscosity [G.H.] of Z1-Z3, an OH solids amount of 2.3-2.5, and a colour [G.H.] maximum of 3. It is used in non-yellowing nitrocell...view more Benasol E 184 is made using synthetic fatty acids, with an oil content of 28% and a solids amount of 70%. This product has a viscosity [G.H.] of Z1-Z3, an OH solids amount of 2.3-2.5, and a colour [G.H.] maximum of 3. It is used in non-yellowing nitrocellulose lacquers for automotive finishes, bake and two-component polyurethane enamels. Benasol E 184 has bake, nitro and catalyze applications. view less | Request Sample |
| Benasol F 71 | Benasedo | Benasol F 71 is used in two-component polyurethane gloss or mat finishes and sealers endowed with high transparence, and has catalyze applications. This product is made using hydrogenated castor oil and vegetable fatty acids, with an oil content of 41%. T...view more Benasol F 71 is used in two-component polyurethane gloss or mat finishes and sealers endowed with high transparence, and has catalyze applications. This product is made using hydrogenated castor oil and vegetable fatty acids, with an oil content of 41%. This product has an OH solids amount of 4.4-4.6, an A.V. solids level of 15-20, a colour [G.H.] maximum of 4, and a viscosity of Z1-Z2. view less | Request Sample |
| Benasol F 73 | Benasedo | Benasol F 73 is used in high-quality clear and pigmented polyurethane finishes for wood, and has catalyze applications. It uses hydrogenated castor oil, with a 43% oil and 60% solids content. This product has a 4.5-4.7% OH solids amount, a 15-23 A.V. soli...view more Benasol F 73 is used in high-quality clear and pigmented polyurethane finishes for wood, and has catalyze applications. It uses hydrogenated castor oil, with a 43% oil and 60% solids content. This product has a 4.5-4.7% OH solids amount, a 15-23 A.V. solids level, and a Y-Z viscosity [G.H.]. view less | Request Sample |
| BENASOL FL 34 | Benasedo | BENASOL FL 34 is a fast air drying long oil alkyd resin, modified with aromatic isocyanate, having a pale colour and giving hard and tough films. It is suggested for clear and pigmented finishes with high gloss, high body, excellent brushability and dryin...view more BENASOL FL 34 is a fast air drying long oil alkyd resin, modified with aromatic isocyanate, having a pale colour and giving hard and tough films. It is suggested for clear and pigmented finishes with high gloss, high body, excellent brushability and drying. It is employed for silk – glossy paints or flat one-coat wall finishes, pigmented sealers for wood and primers endowed with easy sanding properties and applied by brush or roll. Wide compatibility with medium-long-oil alkyd resins. view less | Request Sample |
| BENASOL FL 40 | Benasedo | BENASOL FL 40 is a non yellowing, slightly thixotropic high-molecular weight alkyd resin, endowed with very good flow, fast drying and wide compatibility with medium-long-oil alkyd resins. In combination with medium-oil alkyd resins, is suitable for seale...view more BENASOL FL 40 is a non yellowing, slightly thixotropic high-molecular weight alkyd resin, endowed with very good flow, fast drying and wide compatibility with medium-long-oil alkyd resins. In combination with medium-oil alkyd resins, is suitable for sealers, matt and semi-glossy paints employed in building and costruction industries endowed with good outdoor resistance properties. view less | Request Sample |
| Benasol FX 97 | Benasedo | Benasol FX 97 is a new Alkyd Resin with 98% solid content, which allows the formulators to stay below the requested limits. Benasol FX 97 is easy to apply by brush and widely compatible with different types of resins; due to its properties, can be used as...view more Benasol FX 97 is a new Alkyd Resin with 98% solid content, which allows the formulators to stay below the requested limits. Benasol FX 97 is easy to apply by brush and widely compatible with different types of resins; due to its properties, can be used as grinding vehicle and can be completed with a wide range of Long Oil Alkyd Resins. It is also suggested to improve gloss and build-up of conventional paints. view less | Request Sample |
| Benasol FX66 | Benasedo | Benasol FX66 is used in high performance non-yellowing paints for interior and exterior, for building industry and "do-it-yourself". It provides very good colour retention, and has air applications. This product uses special unsaturated fatty acids, with ...view more Benasol FX66 is used in high performance non-yellowing paints for interior and exterior, for building industry and "do-it-yourself". It provides very good colour retention, and has air applications. This product uses special unsaturated fatty acids, with a 67% oil and 70% solids content. This product has a colour [G.H.] maximum of 3, an A.V. solids amount of 6-10, and a viscosity [G.H.] of Z1-Z2. view less | Request Sample |
| BENASOL GEL 220 | Benasedo | BENASOL GEL 220 is a soft-gel fast drying thixotropic alkyd resin, endowed with very good flow , body and color ritention. It is employed alone or combined with medium-long oil alkyd resins to formulate enamels, glossy paints, flat one-coat wall finishes ...view more BENASOL GEL 220 is a soft-gel fast drying thixotropic alkyd resin, endowed with very good flow , body and color ritention. It is employed alone or combined with medium-long oil alkyd resins to formulate enamels, glossy paints, flat one-coat wall finishes or pigmented sealers for wood and “do it Your self”, applied by brush or roller. view less | Request Sample |
| BENASOL HS 120 | Benasedo | BENASOL HS 120 is an air – dryng, non yellowing, long-oil alkyd resin with a particular molecular structure, endowed with fast air drying, good gloss, colour retention, good flow and superficial hardness. It’s easy to apply by brush and it’s widely compat...view more BENASOL HS 120 is an air – dryng, non yellowing, long-oil alkyd resin with a particular molecular structure, endowed with fast air drying, good gloss, colour retention, good flow and superficial hardness. It’s easy to apply by brush and it’s widely compatible with different types of resins, showing excellent wetting properties. Due to its properties, can be used as grinding vehicle and to produce tinting pastes. It is also suggested to improve gloss and build-up of conventional paints. view less | Request Sample |
| BENASOL HS 6922 | Benasedo | BENASOL HS 6922 is a non yellowing alkyd resin with a particular molecular structure, endowed with very fast air drying, good gloss and colour retention, good flow, superficial hardness. Easy to be applied by brush. It is suggested for white and coloured ...view more BENASOL HS 6922 is a non yellowing alkyd resin with a particular molecular structure, endowed with very fast air drying, good gloss and colour retention, good flow, superficial hardness. Easy to be applied by brush. It is suggested for white and coloured air-drying enamels with high solid content, in the building sector and for internal and external maintenance. view less | Request Sample |
| BENASOL HS 7100 | Benasedo | BENASOL HS 7100 is a non yellowing alkyd resin with a particular molecular structure, endowed with very fast air drying, good gloss and colour retention, good flow, superficial hardness. Easy to be applied by brush. It is suggested for white and coloured ...view more BENASOL HS 7100 is a non yellowing alkyd resin with a particular molecular structure, endowed with very fast air drying, good gloss and colour retention, good flow, superficial hardness. Easy to be applied by brush. It is suggested for white and coloured air-drying enamels with high solid content, in the building sector and for internal and external maintenance. view less | Request Sample |
| BENASOL HS 7380 | Benasedo | BENASOL HS 7380 is a non yellowing alkyd resin with a particular molecular structure, endowed with good air drying, gloss and colour retention. It is suggested for white and coloured air-drying enamels with high solid content, in the building sector and f...view more BENASOL HS 7380 is a non yellowing alkyd resin with a particular molecular structure, endowed with good air drying, gloss and colour retention. It is suggested for white and coloured air-drying enamels with high solid content, in the building sector and for internal and external maintenance in compliance with the CE 2004 – 42 requirements for the VOC reduction . view less | Request Sample |
| BENASOL HS 75 | Benasedo | BENASOL HS 75 is a non yellowing alkyd resin with a particular molecular structure, endowed with very fast air drying, good gloss and colour retention, good flow, superficial hardness and ease of brush application. It is suggested for white and coloured a...view more BENASOL HS 75 is a non yellowing alkyd resin with a particular molecular structure, endowed with very fast air drying, good gloss and colour retention, good flow, superficial hardness and ease of brush application. It is suggested for white and coloured air-drying enamels with high solid content, in the building sector and for internal and external maintenance. view less | Request Sample |
| BENASOL HS 753 | Benasedo | BENASOL HS 753 is a non yellowing alkyd resin , endowed with good air drying, gloss and colour retention. It is suggested for white and coloured air-drying enamels with high solid content, in the building sector and for internal and external maintenance. | Request Sample |
| Benasol HS 754 | Benasedo | Benasol HS 754 is a non yellowing alkyd resin , endowed with good air drying, gloss and colour retention. It is suggested for white and coloured air-drying enamels with high solid content, in the building sector and for internal and external maintenance. | Request Sample |
| BENASOL HS 86 | Benasedo | BENASOL HS 86 is a non yellowing alkyd resin with a particular molecular structure, endowed with very fast air drying, good gloss and colour retention, good flow, superficial hardness. Easy to be applied by brush. It is suggested for white and coloured ai...view more BENASOL HS 86 is a non yellowing alkyd resin with a particular molecular structure, endowed with very fast air drying, good gloss and colour retention, good flow, superficial hardness. Easy to be applied by brush. It is suggested for white and coloured air-drying enamels with high solid content, in the building sector and for internal and external maintenance. view less | Request Sample |
| BENASOL L 50 AV | Benasedo | BENASOL L 50 is an air-drying alkyd resin, endowed with good body, gloss and pigment wetting power. It is suitable for sealers, rust-inhibitive primers, clear and pigmented finishes for building and industrial maintenance both when used alone or in combin...view more BENASOL L 50 is an air-drying alkyd resin, endowed with good body, gloss and pigment wetting power. It is suitable for sealers, rust-inhibitive primers, clear and pigmented finishes for building and industrial maintenance both when used alone or in combination with other alkyd resins. view less | Request Sample |
| BENASOL L 65 | Benasedo | BENASOL L 65 is a long oil, low viscosity alkyd resin,endowed with a very good,trough dryng properties also in thick film, gloss and color retention, hardness,built and brushability. It is suggested for formulating sinthetic enamels, clear and pigmented p...view more BENASOL L 65 is a long oil, low viscosity alkyd resin,endowed with a very good,trough dryng properties also in thick film, gloss and color retention, hardness,built and brushability. It is suggested for formulating sinthetic enamels, clear and pigmented paints for “ Do it Yourself “ and maintenance, alone or combined with oils urethane modified binders. view less | Request Sample |
| Benasol R 126 | Benasedo | Benasol R 126 is used in polyurethane clear finishes and lacquers for wood and metals, with nitro and catalyze applications. It is made using castor oil, with a 53% oil and 60% solids content. This product has an OH solids amount of 5.4-5.6%, a colour [G....view more Benasol R 126 is used in polyurethane clear finishes and lacquers for wood and metals, with nitro and catalyze applications. It is made using castor oil, with a 53% oil and 60% solids content. This product has an OH solids amount of 5.4-5.6%, a colour [G.H.] maximum of 5, and a viscosity [G.H.] of X-Y. view less | Request Sample |
| Benasol R 127 | Benasedo | Benasol R 127 is used in polyurethane high build-up clear finishes and lacquers endowed with good adhesion and flexibility for metals and wood. It is made using castor oil, with a 59% oil and 60% solids content. This product has an OH solids amount of 5.2...view more Benasol R 127 is used in polyurethane high build-up clear finishes and lacquers endowed with good adhesion and flexibility for metals and wood. It is made using castor oil, with a 59% oil and 60% solids content. This product has an OH solids amount of 5.2-5.4%, a colour [G.H.] maximum of 5, a viscosity [G.H.] of W-Y, and an A.V. solids level of 6-15. Benasol R 127 has catalyze and nitro applications. view less | Request Sample |
| BENASOL R 40 D | Benasedo | BENASOL R 40 D is an alkyd resin having good properties of adhesion and flexibility, gloss and colour retention, build – up and flow. It is suitable to produce low temperature bake enamels crosslinked with amino resins. BENASOL R 40 D is also suggested to...view more BENASOL R 40 D is an alkyd resin having good properties of adhesion and flexibility, gloss and colour retention, build – up and flow. It is suitable to produce low temperature bake enamels crosslinked with amino resins. BENASOL R 40 D is also suggested to formulate clear and pigmented acid- curing coatings and nitrocellulose lacquers. view less | Request Sample |
| Benasol RC 45 | Benasedo | Benasol RC 45 is used in polyurethane sealers and mat finishes for wood as well as for nitrocellulose lacquers, and can be used in bake, nitro and catalyze applications. This product uses castor and vegetable fatty acids oil, with a 41% oil and 60% solids...view more Benasol RC 45 is used in polyurethane sealers and mat finishes for wood as well as for nitrocellulose lacquers, and can be used in bake, nitro and catalyze applications. This product uses castor and vegetable fatty acids oil, with a 41% oil and 60% solids content. Benasol RC 45 as a viscosity [G.H.] of Z1-Z3, an A.V. solids amount of 6-15, and an OH solids level of 4.2-4.4%. view less | Request Sample |
| Benasol RC 75 | Benasedo | Benasol RC 75 is used in high-gloss polyurethane finishes and vehicles to improve the general performances of wood systems, with nitro and catalyze applications. It uses castor oil type, with a 78% oil and 80% solids content. This product has an OH solids...view more Benasol RC 75 is used in high-gloss polyurethane finishes and vehicles to improve the general performances of wood systems, with nitro and catalyze applications. It uses castor oil type, with a 78% oil and 80% solids content. This product has an OH solids amount of 5.8-6.0%, an A.V. solids amount of 6-10, a colour [G.H.] maximum 5, and a viscosity [G.H.] of X-Y. view less | Request Sample |
| Benasol RT 43 | Benasedo | Benasol RT 43 is a vehicle to be used alone or combined with other Benasol for polyurethane sealers or mat finishes. It is endowed with high-body and fast drying, and has catalyze applications. This product contains castor and Talloil, with a 43% oil and ...view more Benasol RT 43 is a vehicle to be used alone or combined with other Benasol for polyurethane sealers or mat finishes. It is endowed with high-body and fast drying, and has catalyze applications. This product contains castor and Talloil, with a 43% oil and 60% solids amount. It has a viscosity [G.H.] of Z1-Z2, an A.V. solids amount of 6-15, a color [ G.H.] maximum of 6, and an OH solids levle of 4.0-4.2%. view less | Request Sample |
