| ANTI-TERRA®-203 | BYK | ANTI-TERRA®-203 is a solution of an alkylammonium salt of a polycarboxylic acid. This product is suitable for medium to low polar solvent-borne and solvent-free coating systems. It causes an increase in thixotropy. In highly filled systems, the sagging te...view more ANTI-TERRA®-203 is a solution of an alkylammonium salt of a polycarboxylic acid. This product is suitable for medium to low polar solvent-borne and solvent-free coating systems. It causes an increase in thixotropy. In highly filled systems, the sagging tendency is reduced; in addition, no negative influence on the water sensitivity of the paint film has been observed. When formulated into anti-corrosion primers, the protective properties are enhanced in many instances. view less | |
| ANTI-TERRA®-204 | BYK | ANTI-TERRA®-204 is a solution of a polycarboxylic acid salt of polyamine amides. In comparison to ANTI-TERRA-203, ANTI-TERRA-204 can additionally be used in non-polar systems and is compatible with white spirits. The lower the polarity the more the thixot...view more ANTI-TERRA®-204 is a solution of a polycarboxylic acid salt of polyamine amides. In comparison to ANTI-TERRA-203, ANTI-TERRA-204 can additionally be used in non-polar systems and is compatible with white spirits. The lower the polarity the more the thixotropy is increased. The preferred binders are long, medium and short oil alkyds, PVC-copolymers, chlorinated rubber and epoxy. Even in "low-filled“ systems, the sagging tendency is reduced; in addition, no negative influence on the water sensitivity of the paint film has been observed. When formulated into anticorrosion primers, the protective properties are enhanced in many instances. view less | |
| ANTI-TERRA®-205 | BYK | ANTI-TERRA®-205 is a high molecular weight wetting and dispersing additives for solvent-borne systems. Solution of a polycarboxylic acid salt of polyamine amides. | |
| ANTI-TERRA®-250 | BYK | ANTI-TERRA®-250 is a solution of an alkylolammonium salt of a high molecular weight acidic polymer. It is used in aqueous systems and provides an increase in thixotropy and prevents hard settling of pigments. Due to controlled flocculation mechanism, the ...view more ANTI-TERRA®-250 is a solution of an alkylolammonium salt of a high molecular weight acidic polymer. It is used in aqueous systems and provides an increase in thixotropy and prevents hard settling of pigments. Due to controlled flocculation mechanism, the use of ANTI-TERRA-250 may lead to a minor gloss reduction. view less | |
| ANTI-TERRA®-U | BYK | ANTI-TERRA-U is the standard wetting and dispersing additive for solvent-borne industrial and architectural coatings. It can also be utilized to provide excellent gelling in organo-philic bentonites. This product is composed of a solution of a salt of uns...view more ANTI-TERRA-U is the standard wetting and dispersing additive for solvent-borne industrial and architectural coatings. It can also be utilized to provide excellent gelling in organo-philic bentonites. This product is composed of a solution of a salt of unsaturated polyamine amides and lower molecular weight acidic polyesters. view less | |
| ANTI-TERRA®-U 100 | BYK | ANTI-TERRA-U 100 is the solvent-free version of ANTI-TERRA U , the standard wetting and dispersing additive for solvent-borne industrial and architectural coatings. It can also be used to provide excellent gelation of organophilic bentonites. ANTI-TERR...view more ANTI-TERRA-U 100 is the solvent-free version of ANTI-TERRA U , the standard wetting and dispersing additive for solvent-borne industrial and architectural coatings. It can also be used to provide excellent gelation of organophilic bentonites. ANTI-TERRA-U 100 is effective for wetting and dispersing colored pigments, both organic and inorganic. No adverse effect has been observed on the pot-life of two-component systems or on the dry time of oxidative cure binders. ANTI-TERRA-U 100 can also be used as a wetting and suspending additive in water soluble coatings. view less | |
| AQUACER 1013 | BYK | AQUACER 1013 is a VOC-free HDPE-based wax emulsion for improving the surface protection in aqueous coatings and printing inks as well as in aqueous care products and polishes. | |
| AQUACER 1031 | BYK | AQUACER 1031 is an emulsion based on a polyethylene wax for improving the surface properties of aqueous care products. It offers an anti-slip effect and good foot traffic resistance. | |
| AQUACER 1039 | BYK | AQUACER 1039 is a paraffin wax emulsion for improved surface characteristics in aqueous coatings and printing inks. | |
| AQUACER 1040 | BYK | AQUACER 1040 is a primary polyethylene dispersion for formulating release agents for metal die casting. | |
| AQUACER 1061 | BYK | AQUACER 1061 is an emulsion of an ethylene-acrylic acid copolymer wax for improving the surface characteristics of paper. | |
| AQUACER 1063 | BYK | AQUACER 1063 is a polyethylene dispersion to improve the anti-caking properties of hot-melt adhesives and to increase adhesion in dispersion adhesives for the packaging sector. | |
| AQUACER 1075 | BYK | AQUACER 1075 is an emulsion based on an HD polyethylene wax to improve the surface properties of aqueous care products and polishes, and aqueous printing inks. | |
| AQUACER 1510 | BYK | AQUACER 1510 is a polypropylene wax emulsion for aqueous glass fiber sizings to improve the mechanical properties in glass fiber- reinforced PP compounds. | |
| AQUACER® 1547 | BYK | AQUACER® 1547 is a wax emulsion for improving surface properties of water-borne can coatings. It is an anionic emulsion of an oxidized HD polyethylene wax. This product improves scratch resistance. | |
| AQUACER 2500 | BYK | AQUACER 2500 is a wax emulsion on the basis of modified PE for aqueous foil and paper coatings to improve slip and abrasion resistance. | |
| AQUACER 2650 | BYK | AQUACER 2650 is a wax emulsion based on carnauba wax for aqueous thermal transfer systems, car care products and aqueous leather coatings. It seals and thereby covers any minor scratches on the surface that is to be treated and restores the color of the s...view more AQUACER 2650 is a wax emulsion based on carnauba wax for aqueous thermal transfer systems, car care products and aqueous leather coatings. It seals and thereby covers any minor scratches on the surface that is to be treated and restores the color of the surface. The melting point of 85 °C means that the wax emulsion can easily be polished up using a soft terry cloth or microfiber cloth, but polishing with mechanical tools is also possible. view less | |
| AQUACER 3500 | BYK | AQUACER 3500 is a cationic wax emulsion based on a modified polypropylene wax for formulating release agents for metal die casting. | |
| AQUACER 494 | BYK | AQUACER 494 is an aqueous paraffin wax emulsion for care products and polishes. | |
| AQUACER 497 | BYK | AQUACER 497 is a paraffin-based wax emulsion for aqueous coatings, printing inks as well as care products and polishes for improving water repellency and surface slip. | |
| AQUACER 501 | BYK | AQUACER 501 is an HDPE-based wax emulsion for aqueous systems to improve surface protection. | |
| AQUACER 506 | BYK | AQUACER 506 is an emulsion based on a HD polyethylene wax for improving the surface properties of aqueous care products and polishes. It improves the buffability, increases filling capacity and produces an anti-slip effect. The above-mentioned properties ...view more AQUACER 506 is an emulsion based on a HD polyethylene wax for improving the surface properties of aqueous care products and polishes. It improves the buffability, increases filling capacity and produces an anti-slip effect. The above-mentioned properties are generated by mixing AQUACER 506 with polymers in a ratio of 3:1 (solid wax to solid polymer). A mixing ratio of 1:6 increases the water- and alcohol-resistance, the protection against heel marks (= foot traffic resistance), and the dirt-repellent action. AQUACER 506 is compatible with all known polymer dispersions and plasticizers. view less | |
| AQUACER® 507 | BYK | AQUACER® 507 is an anionic emulsion of an oxidized HD polyethylene wax. It is suitable for use in non-ionic and anionic water-borne automotive systems and industrial paints. This product enhances flip-flop effect, improves the D.O.I. of clear coats, enhan...view more AQUACER® 507 is an anionic emulsion of an oxidized HD polyethylene wax. It is suitable for use in non-ionic and anionic water-borne automotive systems and industrial paints. This product enhances flip-flop effect, improves the D.O.I. of clear coats, enhances hardness and slip, and reduces short wave defects (mottling, Bénard cells). view less | |
| AQUACER® 513 | BYK | AQUACER® 513 is a non-ionic emulsion based on an oxidized HD polyethylene wax. It is suitable for use in aqueous systems and printing inks. This product improves the following surface properties: scratch resistance in aqueous systems, rub resistance in pr...view more AQUACER® 513 is a non-ionic emulsion based on an oxidized HD polyethylene wax. It is suitable for use in aqueous systems and printing inks. This product improves the following surface properties: scratch resistance in aqueous systems, rub resistance in printing inks and black heel marking resistance in parquet lacquers. view less | |
| AQUACER 519 | BYK | AQUACER 519 is an emulsion based on a HD polyethylene wax for improving the surface properties of aqueous care products and polishes. It improves the buffability, increases filling capacity and produces an anti-slip effect. The above-mentioned properties ...view more AQUACER 519 is an emulsion based on a HD polyethylene wax for improving the surface properties of aqueous care products and polishes. It improves the buffability, increases filling capacity and produces an anti-slip effect. The above-mentioned properties are generated by mixing AQUACER 519 with polymers in a ratio of 3:1 (solid wax to solid polymer). A mixing ratio of 1:6 increases the water- and alcohol-resistance, the protection against heel marks (= foot traffic resistance), and the dirt-repellent action. AQUACER 519 is compatible with all known polymer dispersions and plasticizers. view less | |
| AQUACER® 526 | BYK | AQUACER® 526 is a wax emulsion for water-borne effect coatings. It is an emulsion of an anionic modified Ethylene-Vinyl Acetate-Copolymer wax (EVA). This product is suitable for water-borne top coats and base coats. It enhances flip-flop effect, improves ...view more AQUACER® 526 is a wax emulsion for water-borne effect coatings. It is an emulsion of an anionic modified Ethylene-Vinyl Acetate-Copolymer wax (EVA). This product is suitable for water-borne top coats and base coats. It enhances flip-flop effect, improves orientation of effect pigments (aluminum, mica, etc.), reduces short wave defects (mottling, Bénard cells), and there is no negative influence on chemical resistance. view less | |
| AQUACER 527 | BYK | AQUACER 527 is a wax emulsion based on a modified EVA copolymer wax to improve surface characteristics in aqueous coating systems and printing inks. | |
| AQUACER 528 | BYK | AQUACER 528 is an emulsion based on an ethylene-acrylic acid-copolymer wax for improving the surface properties of aqueous care products. It offers strong anti-slip effect and good foot traffic resistance. | |
| AQUACER 530 | BYK | AQUACER 530 is a wax emulsion for improved surface characteristics in aqueous printing inks, overprint varnishes, wood and furniture coatings as well as inkjet inks. | |
| AQUACER® 531 | BYK | AQUACER® 531is a wax emulsion for improving surface properties of water-borne industrial paints and printing inks. It is a non-ionic emulsion based on a modified polyethylene wax. This additive improves the following surface properties: slip, scratch resi...view more AQUACER® 531is a wax emulsion for improving surface properties of water-borne industrial paints and printing inks. It is a non-ionic emulsion based on a modified polyethylene wax. This additive improves the following surface properties: slip, scratch resistance, rub resistance and anti blocking. view less | |
| AQUACER 532 | BYK | AQUACER 532 is an emulsion of a modified HD polyethylene wax for improved surface characteristics in aqueous coating systems. | |
| AQUACER® 533 | BYK | AQUACER® 533 is a wax emulsion on the basis of modified paraffin for aqueous systems to improve surface slip, anti-blocking, and water-resistance. It is typically used in architectural coatings and in the printing inks industry. | |
| AQUACER® 537 | BYK | AQUACER® 537 is an anionic emulsion based on a modified paraffin wax. It is suitable for aqueous systems for furniture- and parquet, industrial- and decorative paints. This product improves the following surface properties: water repellency, anti blocking...view more AQUACER® 537 is an anionic emulsion based on a modified paraffin wax. It is suitable for aqueous systems for furniture- and parquet, industrial- and decorative paints. This product improves the following surface properties: water repellency, anti blocking and slip. view less | |
| AQUACER® 539 | BYK | AQUACER® 539 is a non-ionic emulsion based on a modified paraffin wax. This product is suitable for aqueous systems for furniture- and parquet, industrial- and decorative paints. It improves the following surface properties: slip, water repellency, anti b...view more AQUACER® 539 is a non-ionic emulsion based on a modified paraffin wax. This product is suitable for aqueous systems for furniture- and parquet, industrial- and decorative paints. It improves the following surface properties: slip, water repellency, anti blocking, scratch resistance, rub resistance and soft feel effect. view less | |
| AQUACER 541 | BYK | AQUACER 541 is an aqueous emulsion of a montan ester wax for care products and polishes as well as for aqueous coating systems and leather coatings. | |
| AQUACER® 552 | BYK | AQUACER® 552 is a non-ionic emulsion based on an oxidized HD polyethylene wax. This product is suitable for use in aqueous systems and printing inks. It is used to improve scratch resistance in aqueous systems. | |
| AQUACER 561 | BYK | AQUACER 561 is a beeswax-based wax emulsion to improve surface protection in aqueous care products and coating systems. | |
| AQUACER 565 | BYK | AQUACER 565 is an aqueous carnauba wax emulsion for improving the surface characteristics of care products, polishes, and leather coatings. It seals and thereby covers any minor scratches on the surface that is to be treated and restores the color of the ...view more AQUACER 565 is an aqueous carnauba wax emulsion for improving the surface characteristics of care products, polishes, and leather coatings. It seals and thereby covers any minor scratches on the surface that is to be treated and restores the color of the surface. The melting point of 85 °C means that the wax emulsion can easily be polished up using a soft terry cloth or microfiber cloth, but polishing with mechanical tools is also possible. view less | |
| AQUACER 570 | BYK | AQUACER 570 is a modified Ecolabel-compliant sunflower wax emulsion to improve the surface properties of care products and polishes. It seals and thereby covers any minor scratches on the surface that is to be treated, and restores the surface’s original ...view more AQUACER 570 is a modified Ecolabel-compliant sunflower wax emulsion to improve the surface properties of care products and polishes. It seals and thereby covers any minor scratches on the surface that is to be treated, and restores the surface’s original color. It also improves the hydrophobicity and the oleophobicity of care products and polishes. This product is recommended for maintaining and protecting all types of surfaces, for leather, coated and uncoated surfaces. view less | |
| AQUACER 571 | BYK | AQUACER 571 is a modified rice bran wax emulsion to improve the surface properties of care products, polishes, and aqueous coating systems. | |
| AQUACER 581 | BYK | AQUACER 581 is a wax emulsion based on carnauba wax for aqueous paper coatings to improve surface slip, scratch-resistance, uniformity of printing ink acceptance, and ink setoff. Anti-caking additive for thermoplastics and hotmelts. | |
| AQUACER 582 | BYK | AQUACER 582 is an emulsion based on a polyethylene wax for improving the surface properties of aqueous seed coatings. | |
| AQUACER 583 | BYK | AQUACER 583 is a wax emulsion used to improve the surface characteristics of seed coatings. | |
| AQUACER® 593 | BYK | AQUACER® 593 is a wax emulsion for improving anti slip of water-borne paint systems and printing inks. It is a non-ionic emulsion of a modified polypropylene wax. This product is suitable for use in non-ionic and anionic water-borne paint systems and prin...view more AQUACER® 593 is a wax emulsion for improving anti slip of water-borne paint systems and printing inks. It is a non-ionic emulsion of a modified polypropylene wax. This product is suitable for use in non-ionic and anionic water-borne paint systems and printing inks. view less | |
| AQUACER 595 | BYK | AQUACER 595 is an emulsion based on a modified polypropylene wax for improving the surface properties of aqueous care products. It offers a strong anti-slip effect and good dirt repulsion. In aqueous leather finishes it produces an anti-slip and anti-tack...view more AQUACER 595 is an emulsion based on a modified polypropylene wax for improving the surface properties of aqueous care products. It offers a strong anti-slip effect and good dirt repulsion. In aqueous leather finishes it produces an anti-slip and anti-tack effect. view less | |
| AQUACER 597 | BYK | AQUACER 597 is a cationic wax emulsion based on a modified polypropylene wax for formulating release agents for metal die casting. | |
| AQUACER® 840 | BYK | AQUACER® 840 is a cationic emulsion of an oxidized HD polyethylene wax. This product is suitable for use in non-ionic and anionic water-borne automotive systems and industrial paints. It enhances flip-flop effect, improves the D.O.I. of clear coats, impro...view more AQUACER® 840 is a cationic emulsion of an oxidized HD polyethylene wax. This product is suitable for use in non-ionic and anionic water-borne automotive systems and industrial paints. It enhances flip-flop effect, improves the D.O.I. of clear coats, improves orientation of effect pigments and reduces short wave defects. view less | |
| AQUAMAT® 208 | BYK | AQUAMAT® 208 is an oxidized HD polyethylene wax dispersion. It is suitable for aqueous systems e. g. furniture- and parquet lacquer, industrial- and decorative paints and inks. The additive improves the following surface properties: gloss reduction, scrat...view more AQUAMAT® 208 is an oxidized HD polyethylene wax dispersion. It is suitable for aqueous systems e. g. furniture- and parquet lacquer, industrial- and decorative paints and inks. The additive improves the following surface properties: gloss reduction, scratch resistance and soft feel effect. view less | |
| AQUAMAT® 263 | BYK | AQUAMAT® 263 is an oxidized HD polyethylene wax dispersion. This product is suitable for aqueous systems e. g. furniture- and parquet lacquer, industrial- and decorative paints and inks. The additive improves the following surface properties: gloss reduct...view more AQUAMAT® 263 is an oxidized HD polyethylene wax dispersion. This product is suitable for aqueous systems e. g. furniture- and parquet lacquer, industrial- and decorative paints and inks. The additive improves the following surface properties: gloss reduction, scratch resistance, soft feel effect, rub resistance, anti blocking and black heel resistance. view less | |
| AQUATIX® 8421 | BYK | AQUATIX® 8421 is a non-ionic emulsion of a modified Ethylene-Vinyl-Acetate (EVA) copolymer wax. It improves the rheological properties and brilliance of effect pigment slurries that are co-solvent-free. This product provides the following properties: impr...view more AQUATIX® 8421 is a non-ionic emulsion of a modified Ethylene-Vinyl-Acetate (EVA) copolymer wax. It improves the rheological properties and brilliance of effect pigment slurries that are co-solvent-free. This product provides the following properties: improves effect pigment orientation, reduces cloudiness /mottling, shows less sensivity to co-solvents in coating systems compared to PU based thickeners, is “ready to use”, provides easy handling and incorporation compared to clays or acrylic thickeners, and excellent anti-settling properties in coatings during storage and application. view less | |
| BAL 101 H WS-70 | Bonyan Kala Chemie Co. | BAL 101 H WS-70 is a long oil alkyd resin that is used for its hardness, drying, gloss retention, adhesion, and coverage properties. This product has a viscosity of 800-1500 stoke at 25°C and is used in industrial varnishes, wood and metal coatings, and g...view more BAL 101 H WS-70 is a long oil alkyd resin that is used for its hardness, drying, gloss retention, adhesion, and coverage properties. This product has a viscosity of 800-1500 stoke at 25°C and is used in industrial varnishes, wood and metal coatings, and gloss and semi gloss architectural paints. view less | |
| BAL 101 L WS-70 | Bonyan Kala Chemie Co. | BAL 101 L WS-70 is a long oil alkyd resin that is used for its hardness, drying, gloss retention, adhesion, and coverage properties. This product has a viscosity of 350-650 stoke at 25°C and is used in industrial varnishes, metal structural coatings, and ...view more BAL 101 L WS-70 is a long oil alkyd resin that is used for its hardness, drying, gloss retention, adhesion, and coverage properties. This product has a viscosity of 350-650 stoke at 25°C and is used in industrial varnishes, metal structural coatings, and gloss and semi gloss architectural paints. view less | |
| BAL 102 WS-70 | Bonyan Kala Chemie Co. | BAL 102 WS-70 is a long oil alkyd resin that is used for its coverage, drying, gloss retention, pigment wetting, and dispersing properties. This product has a viscosity of 250-500 stoke at 25°C and is mainly used as a paste in architectural paints, and in...view more BAL 102 WS-70 is a long oil alkyd resin that is used for its coverage, drying, gloss retention, pigment wetting, and dispersing properties. This product has a viscosity of 250-500 stoke at 25°C and is mainly used as a paste in architectural paints, and in architectural and industrial varnishes. view less | |
| BAL 103 WS-70 | Bonyan Kala Chemie Co. | BAL 103 WS-70 is a long oil alkyd resin that is used for its hardness, drying, gloss retention, adhesion, pigment wetting, dispersing, and coverage properties. This product has a viscosity of 330-550 stoke at 25°C and is used in industrial varnishes, wood...view more BAL 103 WS-70 is a long oil alkyd resin that is used for its hardness, drying, gloss retention, adhesion, pigment wetting, dispersing, and coverage properties. This product has a viscosity of 330-550 stoke at 25°C and is used in industrial varnishes, wood and metal coatings, and gloss and semi gloss architectural paints. view less | |
| BAL 104 WS-70 | Bonyan Kala Chemie Co. | BAL 104 WS-70 is a long oil alkyd resin that is used for its solvent acceptation and filler accountability properties. This product has a viscosity of 1000-3500 stoke at 25°C and is mainly used in metal structural coatings, industrial, wood, metal, anti-c...view more BAL 104 WS-70 is a long oil alkyd resin that is used for its solvent acceptation and filler accountability properties. This product has a viscosity of 1000-3500 stoke at 25°C and is mainly used in metal structural coatings, industrial, wood, metal, anti-corrosion and anti-rust primers. view less | |
| BAL 106 H WS-70 | Bonyan Kala Chemie Co. | BAL 106 H WS-70 is a long oil alkyd resin that is used for its drying, gloss retention, solvent acceptation, good coverage and filler accountability properties. This product has a viscosity of 500-1500 stoke at 25°C and is mainly used in metal structural,...view more BAL 106 H WS-70 is a long oil alkyd resin that is used for its drying, gloss retention, solvent acceptation, good coverage and filler accountability properties. This product has a viscosity of 500-1500 stoke at 25°C and is mainly used in metal structural, wood, and metal coatings, as well as gloss and semi gloss architectural paints. view less | |
| BAL 106 L WS-70 | Bonyan Kala Chemie Co. | BAL 106 L WS-70 is a long oil alkyd resin that is used for its drying, gloss retention, pigment wetting, good coverage and dispersing properties. This product has a viscosity of 300-500 stoke at 25°C and is mainly used in metal structural, wood, and metal...view more BAL 106 L WS-70 is a long oil alkyd resin that is used for its drying, gloss retention, pigment wetting, good coverage and dispersing properties. This product has a viscosity of 300-500 stoke at 25°C and is mainly used in metal structural, wood, and metal coatings, spray paints, as well as gloss and semi gloss architectural paints. view less | |
| BAL 108 WS-70 | Bonyan Kala Chemie Co. | BAL 108 WS-70 is a long oil alkyd resin that is used for its hardness, drying, gloss retention, solvent acceptation, good coverage and adhesion properties. This product has a viscosity of 500-1000 stoke at 25°C and is mainly used in metal structural, wood...view more BAL 108 WS-70 is a long oil alkyd resin that is used for its hardness, drying, gloss retention, solvent acceptation, good coverage and adhesion properties. This product has a viscosity of 500-1000 stoke at 25°C and is mainly used in metal structural, wood, and metal coatings, as well as gloss and semi gloss architectural paints. view less | |
| BAL 116 WS-70 | Bonyan Kala Chemie Co. | BAL 116 WS-70 is a long oil alkyd resin that is used for its drying, gloss retention, solvent acceptation, hardness and filler accountability properties. This product has a viscosity of 1000-2500 stoke at 25°C and is mainly used in metal structural, wood,...view more BAL 116 WS-70 is a long oil alkyd resin that is used for its drying, gloss retention, solvent acceptation, hardness and filler accountability properties. This product has a viscosity of 1000-2500 stoke at 25°C and is mainly used in metal structural, wood, and metal coatings, as well as gloss and semi gloss architectural paints. view less | |
| BAL 118 WS-70 | Bonyan Kala Chemie Co. | BAL 118 WS-70 is a long oil alkyd resin that is used for its drying, gloss retention, solvent acceptation, good coverage and filler accountability properties. This product has a viscosity of 1000-3000 stoke at 25°C and is mainly used in wood and metal coa...view more BAL 118 WS-70 is a long oil alkyd resin that is used for its drying, gloss retention, solvent acceptation, good coverage and filler accountability properties. This product has a viscosity of 1000-3000 stoke at 25°C and is mainly used in wood and metal coatings, as well as gloss and semi gloss architectural paints. view less | |
| BAL 120 WS-70 | Bonyan Kala Chemie Co. | BAL 120 WS-70 is a long oil alkyd resin that is used for its drying, gloss retention, solvent acceptation, good coverage and solvent acceptation properties. This product has a viscosity of 300-700 stoke at 25°C and is mainly used in wood and metal coating...view more BAL 120 WS-70 is a long oil alkyd resin that is used for its drying, gloss retention, solvent acceptation, good coverage and solvent acceptation properties. This product has a viscosity of 300-700 stoke at 25°C and is mainly used in wood and metal coatings, as well as gloss and semi gloss architectural paints. view less | |
| BAM 202 WS-55 | Bonyan Kala Chemie Co. | BAM 202 WS-55 is a medium oil alkyd resin that is used for its surface and deep drying, gloss retention, adhesion and flexibility, solvent acceptation, hardness, and pigment wetting and dispersing properties. This product has a viscosity of 350-900 stoke ...view more BAM 202 WS-55 is a medium oil alkyd resin that is used for its surface and deep drying, gloss retention, adhesion and flexibility, solvent acceptation, hardness, and pigment wetting and dispersing properties. This product has a viscosity of 350-900 stoke at 25°C and is mainly used in zinc chromate primers, industrial machinery coatings, metal structural coatings, and spray, auto body repair and industrial air-drying paints. view less | |
| BAM 203 X-60 | Bonyan Kala Chemie Co. | BAM 203 X-60 is a medium oil alkyd resin that is used for its surface and deep drying, gloss retention, adhesion and flexibility, solvent acceptation, hardness, and pigment wetting and dispersing properties. This product has a viscosity of 50-100 stoke at...view more BAM 203 X-60 is a medium oil alkyd resin that is used for its surface and deep drying, gloss retention, adhesion and flexibility, solvent acceptation, hardness, and pigment wetting and dispersing properties. This product has a viscosity of 50-100 stoke at 25°C and is mainly used in auto body repair paints, metallic paints, industrial machinery coatings, metal structural coatings, and industrial air-drying paints. view less | |
| BAM 204 WS-50 | Bonyan Kala Chemie Co. | BAM 204 WS-50 is a medium oil alkyd resin that is used for its surface and deep drying, gloss retention, adhesion and flexibility, solvent acceptation, hardness, and pigment wetting and dispersing properties. This product has a viscosity of 150-350 stoke ...view more BAM 204 WS-50 is a medium oil alkyd resin that is used for its surface and deep drying, gloss retention, adhesion and flexibility, solvent acceptation, hardness, and pigment wetting and dispersing properties. This product has a viscosity of 150-350 stoke at 25°C and is mainly used in cabinet and spray paints, industrial air-drying paints, metal structural coatings, industrial machinery coatings, paste for architectural paints, and anti-corrosion primers. view less | |
| BAM 208 WSX-55 | Bonyan Kala Chemie Co. | BAM 208 WSX-55 is a medium oil alkyd resin that is used for its surface and deep drying, gloss retention, adhesion and flexibility, solvent acceptation, hardness, and pigment wetting and dispersing properties. This product has a viscosity of 80-180 stoke ...view more BAM 208 WSX-55 is a medium oil alkyd resin that is used for its surface and deep drying, gloss retention, adhesion and flexibility, solvent acceptation, hardness, and pigment wetting and dispersing properties. This product has a viscosity of 80-180 stoke at 25°C and is mainly used in auto body repair paints, industrial machinery coatings, cabinet and spray paints, and industrial air-drying paints. view less | |
| BAM 212 X-60 | Bonyan Kala Chemie Co. | BAM 212 X-60 is a medium oil alkyd resin that is used for its surface and deep drying, gloss retention, adhesion and flexibility, solvent acceptation, hardness, and pigment wetting and dispersing properties. This product has a viscosity of 60-90 stoke at ...view more BAM 212 X-60 is a medium oil alkyd resin that is used for its surface and deep drying, gloss retention, adhesion and flexibility, solvent acceptation, hardness, and pigment wetting and dispersing properties. This product has a viscosity of 60-90 stoke at 25°C and is mainly used in auto body repair paints, industrial machinery coatings, metallic paints, industrial air-drying paints, and paint paste. view less | |
| BAS 302 X-60 | Bonyan Kala Chemie Co. | BAS 302 X-60 is a short oil alkyd resin that is used for its gloss retention, adhesion and flexibility, solvent acceptation, hardness, and pigment wetting and dispersing properties. This product has a viscosity of 50-80 stoke at 25°C and is mainly used in...view more BAS 302 X-60 is a short oil alkyd resin that is used for its gloss retention, adhesion and flexibility, solvent acceptation, hardness, and pigment wetting and dispersing properties. This product has a viscosity of 50-80 stoke at 25°C and is mainly used in nitro-cellulose paints and lacquers, alkyd amin varnishes, amino resin based stoving paints, acid curing coatings, and printing inks. view less | |
| BAS 305 X-50 | Bonyan Kala Chemie Co. | BAS 305 X-50 is a short oil alkyd resin that is used for its gloss retention, adhesion and flexibility, solvent acceptation, hardness, and pigment wetting and dispersing properties. This product has a viscosity of 40-90 stoke at 25°C and is mainly used in...view more BAS 305 X-50 is a short oil alkyd resin that is used for its gloss retention, adhesion and flexibility, solvent acceptation, hardness, and pigment wetting and dispersing properties. This product has a viscosity of 40-90 stoke at 25°C and is mainly used in hammer finish paints, anti-corrosion primers, fast dry paints, and industrial air-drying paints. view less | |
| BAS 307 X-60 | Bonyan Kala Chemie Co. | BAS 307 X-60 is a short oil alkyd resin that is used for its gloss retention, adhesion and flexibility, solvent acceptation, hardness, and pigment wetting and dispersing properties. This product has a viscosity of 250-450 stoke at 25°C and is mainly used ...view more BAS 307 X-60 is a short oil alkyd resin that is used for its gloss retention, adhesion and flexibility, solvent acceptation, hardness, and pigment wetting and dispersing properties. This product has a viscosity of 250-450 stoke at 25°C and is mainly used in nitro-cellulose lacquers, amino resin based stoving paints, acid curing coatings, and auto parts stoving paints. view less | |
| BAS 310 H X-60 | Bonyan Kala Chemie Co. | BAS 310 H X-60 is a short oil alkyd resin that is used for its gloss retention, adhesion and flexibility, solvent acceptation, hardness, and pigment wetting and dispersing properties. This product has a viscosity of 200-400 stoke at 25°C and is mainly use...view more BAS 310 H X-60 is a short oil alkyd resin that is used for its gloss retention, adhesion and flexibility, solvent acceptation, hardness, and pigment wetting and dispersing properties. This product has a viscosity of 200-400 stoke at 25°C and is mainly used in nitro-cellulose paints and lacquers, alkyd amin varnishes, acid curing coatings, and anti-corrosion primers. view less | |
| BAS 310 L X-60 | Bonyan Kala Chemie Co. | BAS 310 L X-60 is a short oil alkyd resin that is used for its gloss retention, adhesion and flexibility, solvent acceptation, hardness, and pigment wetting and dispersing properties. This product has a viscosity of 100-200 stoke at 25°C and is mainly use...view more BAS 310 L X-60 is a short oil alkyd resin that is used for its gloss retention, adhesion and flexibility, solvent acceptation, hardness, and pigment wetting and dispersing properties. This product has a viscosity of 100-200 stoke at 25°C and is mainly used in nitro-cellulose paints and lacquers, alkyd amin varnishes, acid curing coatings, and anti-corrosion primers. view less | |
| BAS 312 X-60 | Bonyan Kala Chemie Co. | BAS 312 X-60 is a short oil alkyd resin that is used for its gloss retention, adhesion and flexibility, solvent acceptation, hardness, and pigment wetting and dispersing properties. This product has a viscosity of 80-120 stoke at 25°C and is mainly used i...view more BAS 312 X-60 is a short oil alkyd resin that is used for its gloss retention, adhesion and flexibility, solvent acceptation, hardness, and pigment wetting and dispersing properties. This product has a viscosity of 80-120 stoke at 25°C and is mainly used in nitro-cellulose paints, alkyd amin lacquers, and anti-corrosion primers. view less | |
| BAS 313 X-60 | Bonyan Kala Chemie Co. | BAS 313 X-60 is a short oil alkyd resin that is used for its gloss retention, adhesion and flexibility, solvent acceptation, hardness, and pigment wetting and dispersing properties. This product has a viscosity of 600-1000 stoke at 25°C and is mainly used...view more BAS 313 X-60 is a short oil alkyd resin that is used for its gloss retention, adhesion and flexibility, solvent acceptation, hardness, and pigment wetting and dispersing properties. This product has a viscosity of 600-1000 stoke at 25°C and is mainly used in nitro-cellulose paints, alkyd amin lacquers, and anti-corrosion primers. view less | |
| BD-Ca-5 | Bonyan Kala Chemie Co. | BD-Ca-5 is a drier that appears as a clear yellow liquid. This product is an auxiliary drier and has a metal content of 5±0.2. It is often used for air through and surface drying systems. | |
| BD-Co-10 | Bonyan Kala Chemie Co. | BD-Co-10 is a drier that appears as a violet liquid. This product is an active oxidation drier and has a metal content of 10±0.2. It is often used as an accelerator for unsaturated polyester resins and in air drying systems. | |
| BD-Pb-32 | Bonyan Kala Chemie Co. | BD-Pb-32 is a drier that appears as a clear yellow liquid. This product is a through drier and has a metal content of 32±0.5. It is often used for air through and surface drying systems. | |
| BD-Zr-18 | Bonyan Kala Chemie Co. | BD-Zr-18 is a drier that appears as a light yellow liquid. This product is a through drier and has a metal content of 18±0.3. It is often used in air drying systems, metallic paints, metallic varnishes and coatings. | |
| BENTOLITE-L 10 | BYK | BENTOLITE-L 10 is a low iron rheology additive based on natural bentonite for aqueous plastic refractories. | |
| BENTOLITE-L 3 | BYK | BENTOLITE-L 3 is a low iron rheology additive based on natural bentonite for aqueous plastic refractories. | |
| BUP 612 | Bonyan Kala Chemie Co. | BUP 612 is an unsaturated polyester resin that is used for its moderate gel time, good adhesion to glass fibers, medium viscosity, good physical and mechanical properties after curing, and good flexibility and good resistant to impact. This product has a ...view more BUP 612 is an unsaturated polyester resin that is used for its moderate gel time, good adhesion to glass fibers, medium viscosity, good physical and mechanical properties after curing, and good flexibility and good resistant to impact. This product has a viscosity of 550-750CP at 25°C and is commonly used in general purpose applications. view less | |
| BUP 615 | Bonyan Kala Chemie Co. | BUP 615 is an unsaturated polyester resin that is used for its low color, good adhesion to glass fibers, medium viscosity, and good physical and mechanical properties after curing. This product has a viscosity of 380-480CP at 25°C and is commonly used in ...view more BUP 615 is an unsaturated polyester resin that is used for its low color, good adhesion to glass fibers, medium viscosity, and good physical and mechanical properties after curing. This product has a viscosity of 380-480CP at 25°C and is commonly used in general purpose applications. view less | |
| BUP 620 | Bonyan Kala Chemie Co. | BUP 620 is an unsaturated polyester resin that is used for its low color, excellent adhesion to glass fibers, medium viscosity, good physical and mechanical properties after curing, and filler appropriate accountability properties. This product has a visc...view more BUP 620 is an unsaturated polyester resin that is used for its low color, excellent adhesion to glass fibers, medium viscosity, good physical and mechanical properties after curing, and filler appropriate accountability properties. This product has a viscosity of 400-650CP at 25°C and is commonly used in general purpose applications and goods that need high transparency. view less | |
| BUP 621 | Bonyan Kala Chemie Co. | BUP 621 is an unsaturated polyester resin that is used for its low color, good adhesion to glass fibers, medium viscosity, good physical and mechanical properties after curing, and filler appropriate accountability properties. This product has a viscosity...view more BUP 621 is an unsaturated polyester resin that is used for its low color, good adhesion to glass fibers, medium viscosity, good physical and mechanical properties after curing, and filler appropriate accountability properties. This product has a viscosity of 380-480CP at 25°C and is commonly used in general purpose applications. view less | |
| BUP 623 | Bonyan Kala Chemie Co. | BUP 623 is an unsaturated polyester resin that is used for its good adhesion to glass fibers, medium viscosity, good physical and mechanical properties after curing, limited shrinkage, and filler appropriate accountability properties. This product has a v...view more BUP 623 is an unsaturated polyester resin that is used for its good adhesion to glass fibers, medium viscosity, good physical and mechanical properties after curing, limited shrinkage, and filler appropriate accountability properties. This product has a viscosity of 500-700CP at 25°C and is commonly used in general purpose applications. view less | |
| BUP 624 | Bonyan Kala Chemie Co. | BUP 624 is an unsaturated polyester resin that is used for its low color, medium viscosity, good physical and mechanical properties after curing, resistant to UV, and filler appropriate accountability properties. This product has a viscosity of 450-700CP ...view more BUP 624 is an unsaturated polyester resin that is used for its low color, medium viscosity, good physical and mechanical properties after curing, resistant to UV, and filler appropriate accountability properties. This product has a viscosity of 450-700CP at 25°C and is commonly used in general purpose applications. view less | |
| BUP 625 | Bonyan Kala Chemie Co. | BUP 625 is an unsaturated polyester resin that is used for its medium viscosity, good physical and mechanical properties after curing, and good flexibility and good resistant to impact. This product has a viscosity of 350-500CP at 25°C and is commonly use...view more BUP 625 is an unsaturated polyester resin that is used for its medium viscosity, good physical and mechanical properties after curing, and good flexibility and good resistant to impact. This product has a viscosity of 350-500CP at 25°C and is commonly used in general purpose applications. view less | |
| BUP 626 | Bonyan Kala Chemie Co. | BUP 626 is an unsaturated polyester resin that is used for its low color, limited water absorption, medium viscosity, good physical and mechanical properties after curing, and good flexibility and good resistant to impact. This product has a viscosity of ...view more BUP 626 is an unsaturated polyester resin that is used for its low color, limited water absorption, medium viscosity, good physical and mechanical properties after curing, and good flexibility and good resistant to impact. This product has a viscosity of 450-650CP at 25°C and is commonly used in general purpose applications. view less | |
| BUP 629 | Bonyan Kala Chemie Co. | BUP 629 is an unsaturated polyester resin that is used for its low color, good adhesion to glass fibers, medium viscosity, good physical and mechanical properties after curing, and good flexibility and good resistant to impact. This product has a viscosit...view more BUP 629 is an unsaturated polyester resin that is used for its low color, good adhesion to glass fibers, medium viscosity, good physical and mechanical properties after curing, and good flexibility and good resistant to impact. This product has a viscosity of 700-1000CP at 25°C and is commonly used in general purpose applications and goods that need high transparency. view less | |
| BUP 630 | Bonyan Kala Chemie Co. | BUP 630 is an unsaturated polyester resin that is used for its low color, good adhesion to glass fibers, medium viscosity, good physical and mechanical properties after curing, limited water absorption, resistant to hydrolysis, and good flexibility and go...view more BUP 630 is an unsaturated polyester resin that is used for its low color, good adhesion to glass fibers, medium viscosity, good physical and mechanical properties after curing, limited water absorption, resistant to hydrolysis, and good flexibility and good resistant to impact. This product has a viscosity of 450-700CP at 25°C and is commonly used in general purpose applications and gel coats. view less | |
| BUP 631 | Bonyan Kala Chemie Co. | BUP 631 is an unsaturated polyester resin that is used for its moderate gel time, good adhesion to glass fibers, medium viscosity, good physical and mechanical properties after curing, limited water absorption, and resistant to hydrolysis. This product ha...view more BUP 631 is an unsaturated polyester resin that is used for its moderate gel time, good adhesion to glass fibers, medium viscosity, good physical and mechanical properties after curing, limited water absorption, and resistant to hydrolysis. This product has a viscosity of 700-1000CP at 25°C and is commonly used in general purpose applications. view less | |
| BUP 640 | Bonyan Kala Chemie Co. | BUP 640 is an unsaturated polyester resin that is used for its low gel time, low color, high viscosity, good physical and mechanical properties after curing, and good flexibility and good transparency. This product has a viscosity of 1200-1700CP at 25°C a...view more BUP 640 is an unsaturated polyester resin that is used for its low gel time, low color, high viscosity, good physical and mechanical properties after curing, and good flexibility and good transparency. This product has a viscosity of 1200-1700CP at 25°C and is commonly used in general purpose applications and goods that need high transparency. view less | |
| BUP 643 | Bonyan Kala Chemie Co. | BUP 643 is an unsaturated polyester resin that is used for its low gel time, medium viscosity, good physical and mechanical properties after curing, and good flexibility and good resistance to impact. This product has a viscosity of 900-1500CP at 25°C and...view more BUP 643 is an unsaturated polyester resin that is used for its low gel time, medium viscosity, good physical and mechanical properties after curing, and good flexibility and good resistance to impact. This product has a viscosity of 900-1500CP at 25°C and is commonly used in general purpose applications. view less | |
| BUP 660 | Bonyan Kala Chemie Co. | BUP 660 is an unsaturated polyester resin that is used for its low color, good adhesion to glass fibers, medium viscosity, good physical and mechanical properties after curing, limited water absorption, and resistant to hydrolysis. This product has a visc...view more BUP 660 is an unsaturated polyester resin that is used for its low color, good adhesion to glass fibers, medium viscosity, good physical and mechanical properties after curing, limited water absorption, and resistant to hydrolysis. This product has a viscosity of 600-900CP at 25°C and is commonly used in general purpose applications and gel coats. view less | |
| BUP 665 | Bonyan Kala Chemie Co. | BUP 665 is an unsaturated polyester resin that is used for its low color, good adhesion to glass fibers, medium viscosity, good physical and mechanical properties after curing, limited water absorption, and resistant to hydrolysis. This product has a visc...view more BUP 665 is an unsaturated polyester resin that is used for its low color, good adhesion to glass fibers, medium viscosity, good physical and mechanical properties after curing, limited water absorption, and resistant to hydrolysis. This product has a viscosity of 800-1200CP at 25°C and is commonly used in general purpose applications and gel coats. view less | |
| BUP 690 | Bonyan Kala Chemie Co. | BUP 690 is an unsaturated polyester resin that is used for its moderate gel time, low viscosity, good physical and mechanical properties after curing, and filler appropriate accountability properties. This product has a viscosity of 300-450CP at 25°C and ...view more BUP 690 is an unsaturated polyester resin that is used for its moderate gel time, low viscosity, good physical and mechanical properties after curing, and filler appropriate accountability properties. This product has a viscosity of 300-450CP at 25°C and is commonly used in general purpose applications. view less | |
| BYK-011 | BYK | BYK-011 is a silicone-free, polymer-based defoamer for aqueous coating systems (also radiation curable systems). It is particularly recommended for two pack polyurethane systems and offers very good recoatability. | |
| BYK®-012 | BYK | BYK®-012 is a compound of foam-destroying polymers and hydrophobic particles. This product is especially suitable for defoaming emulsion paints and plasters with a PVC-range of 30-85, where it prevents foam during production and application. The product i...view more BYK®-012 is a compound of foam-destroying polymers and hydrophobic particles. This product is especially suitable for defoaming emulsion paints and plasters with a PVC-range of 30-85, where it prevents foam during production and application. The product is silicone- and mineral oil-free and is specifically recommended for VOC-free systems. The additive shows optimum efficiency at low dosage, is acid and alkaline resistant and can be used in a pH-range of 3 - 12. The product may lead to turbidity and seeding in clear coats. view less | |
| BYK®-014 | BYK | BYK®-014 is a mixture of foam-destroying polymers, fat derivatives and hydrophobic particles. This product shows excellent defoaming properties in various emulsion types such as acrylates, styrene acrylics or VAE´s (vinyl acetate ethylene). It is especial...view more BYK®-014 is a mixture of foam-destroying polymers, fat derivatives and hydrophobic particles. This product shows excellent defoaming properties in various emulsion types such as acrylates, styrene acrylics or VAE´s (vinyl acetate ethylene). It is especially suitable for defoaming emulsion paints and plasters with a PVC range of 30-85. The product is silicone-free and mineral oil-free and is specifically recommended for VOC-free systems. The additive shows optimum efficiency at low dosage, is acid and alkaline resistant, and can be used in a pH range of 3 - 12. view less | |
| BYK-015 | BYK | BYK-015 is a silicone-free, polymer-based defoamer with anti-popping properties for aqueous coatings. Particularly recommended for automotive and industrial coatings. | |
| BYK®-016 | BYK | BYK®-016 is a compound of foam-destroying polymers and hydrophobic particles. It is a very effective silicone- and mineral oil free defoamer. It has no negative influence on the printing behavior and does not cause defects in the typography. At the time o...view more BYK®-016 is a compound of foam-destroying polymers and hydrophobic particles. It is a very effective silicone- and mineral oil free defoamer. It has no negative influence on the printing behavior and does not cause defects in the typography. At the time of publication the active compound in BYK-016 fully meets all requirements of the European Union for "materials and articles in contact with foodstuffs“, and complies with FDA 21 CFR § 175.105, 175.300, 175.320, 176.200, 176.210. view less |
