ANTI-TERRA®-203 | BYK | ANTI-TERRA®-203 is a solution of an alkylammonium salt of a polycarboxylic acid. This product is suitable for medium to low polar solvent-borne and solvent-free coating systems. It causes an increase in thixotropy. In highly filled systems, the sagging te...view more ANTI-TERRA®-203 is a solution of an alkylammonium salt of a polycarboxylic acid. This product is suitable for medium to low polar solvent-borne and solvent-free coating systems. It causes an increase in thixotropy. In highly filled systems, the sagging tendency is reduced; in addition, no negative influence on the water sensitivity of the paint film has been observed. When formulated into anti-corrosion primers, the protective properties are enhanced in many instances. view less | |
ANTI-TERRA®-204 | BYK | ANTI-TERRA®-204 is a solution of a polycarboxylic acid salt of polyamine amides. In comparison to ANTI-TERRA-203, ANTI-TERRA-204 can additionally be used in non-polar systems and is compatible with white spirits. The lower the polarity the more the thixot...view more ANTI-TERRA®-204 is a solution of a polycarboxylic acid salt of polyamine amides. In comparison to ANTI-TERRA-203, ANTI-TERRA-204 can additionally be used in non-polar systems and is compatible with white spirits. The lower the polarity the more the thixotropy is increased. The preferred binders are long, medium and short oil alkyds, PVC-copolymers, chlorinated rubber and epoxy. Even in "low-filled“ systems, the sagging tendency is reduced; in addition, no negative influence on the water sensitivity of the paint film has been observed. When formulated into anticorrosion primers, the protective properties are enhanced in many instances. view less | |
ANTI-TERRA®-205 | BYK | ANTI-TERRA®-205 is a high molecular weight wetting and dispersing additives for solvent-borne systems. Solution of a polycarboxylic acid salt of polyamine amides. | |
ANTI-TERRA®-250 | BYK | ANTI-TERRA®-250 is a solution of an alkylolammonium salt of a high molecular weight acidic polymer. It is used in aqueous systems and provides an increase in thixotropy and prevents hard settling of pigments. Due to controlled flocculation mechanism, the ...view more ANTI-TERRA®-250 is a solution of an alkylolammonium salt of a high molecular weight acidic polymer. It is used in aqueous systems and provides an increase in thixotropy and prevents hard settling of pigments. Due to controlled flocculation mechanism, the use of ANTI-TERRA-250 may lead to a minor gloss reduction. view less | |
ANTI-TERRA®-U | BYK | ANTI-TERRA-U is the standard wetting and dispersing additive for solvent-borne industrial and architectural coatings. It can also be utilized to provide excellent gelling in organo-philic bentonites. This product is composed of a solution of a salt of uns...view more ANTI-TERRA-U is the standard wetting and dispersing additive for solvent-borne industrial and architectural coatings. It can also be utilized to provide excellent gelling in organo-philic bentonites. This product is composed of a solution of a salt of unsaturated polyamine amides and lower molecular weight acidic polyesters. view less | |
ANTI-TERRA®-U 100 | BYK | ANTI-TERRA-U 100 is the solvent-free version of ANTI-TERRA U , the standard wetting and dispersing additive for solvent-borne industrial and architectural coatings. It can also be used to provide excellent gelation of organophilic bentonites. ANTI-TERR...view more ANTI-TERRA-U 100 is the solvent-free version of ANTI-TERRA U , the standard wetting and dispersing additive for solvent-borne industrial and architectural coatings. It can also be used to provide excellent gelation of organophilic bentonites. ANTI-TERRA-U 100 is effective for wetting and dispersing colored pigments, both organic and inorganic. No adverse effect has been observed on the pot-life of two-component systems or on the dry time of oxidative cure binders. ANTI-TERRA-U 100 can also be used as a wetting and suspending additive in water soluble coatings. view less | |
AQUACER 1013 | BYK | AQUACER 1013 is a VOC-free HDPE-based wax emulsion for improving the surface protection in aqueous coatings and printing inks as well as in aqueous care products and polishes. | |
AQUACER 1031 | BYK | AQUACER 1031 is an emulsion based on a polyethylene wax for improving the surface properties of aqueous care products. It offers an anti-slip effect and good foot traffic resistance. | |
AQUACER 1039 | BYK | AQUACER 1039 is a paraffin wax emulsion for improved surface characteristics in aqueous coatings and printing inks. | |
AQUACER 1040 | BYK | AQUACER 1040 is a primary polyethylene dispersion for formulating release agents for metal die casting. | |
AQUACER 1061 | BYK | AQUACER 1061 is an emulsion of an ethylene-acrylic acid copolymer wax for improving the surface characteristics of paper. | |
AQUACER 1063 | BYK | AQUACER 1063 is a polyethylene dispersion to improve the anti-caking properties of hot-melt adhesives and to increase adhesion in dispersion adhesives for the packaging sector. | |
AQUACER 1075 | BYK | AQUACER 1075 is an emulsion based on an HD polyethylene wax to improve the surface properties of aqueous care products and polishes, and aqueous printing inks. | |
AQUACER 1510 | BYK | AQUACER 1510 is a polypropylene wax emulsion for aqueous glass fiber sizings to improve the mechanical properties in glass fiber- reinforced PP compounds. | |
AQUACER® 1547 | BYK | AQUACER® 1547 is a wax emulsion for improving surface properties of water-borne can coatings. It is an anionic emulsion of an oxidized HD polyethylene wax. This product improves scratch resistance. | |
AQUACER 2500 | BYK | AQUACER 2500 is a wax emulsion on the basis of modified PE for aqueous foil and paper coatings to improve slip and abrasion resistance. | |
AQUACER 2650 | BYK | AQUACER 2650 is a wax emulsion based on carnauba wax for aqueous thermal transfer systems, car care products and aqueous leather coatings. It seals and thereby covers any minor scratches on the surface that is to be treated and restores the color of the s...view more AQUACER 2650 is a wax emulsion based on carnauba wax for aqueous thermal transfer systems, car care products and aqueous leather coatings. It seals and thereby covers any minor scratches on the surface that is to be treated and restores the color of the surface. The melting point of 85 °C means that the wax emulsion can easily be polished up using a soft terry cloth or microfiber cloth, but polishing with mechanical tools is also possible. view less | |
AQUACER 3500 | BYK | AQUACER 3500 is a cationic wax emulsion based on a modified polypropylene wax for formulating release agents for metal die casting. | |
AQUACER 494 | BYK | AQUACER 494 is an aqueous paraffin wax emulsion for care products and polishes. | |
AQUACER 497 | BYK | AQUACER 497 is a paraffin-based wax emulsion for aqueous coatings, printing inks as well as care products and polishes for improving water repellency and surface slip. | |
AQUACER 501 | BYK | AQUACER 501 is an HDPE-based wax emulsion for aqueous systems to improve surface protection. | |
AQUACER 506 | BYK | AQUACER 506 is an emulsion based on a HD polyethylene wax for improving the surface properties of aqueous care products and polishes. It improves the buffability, increases filling capacity and produces an anti-slip effect. The above-mentioned properties ...view more AQUACER 506 is an emulsion based on a HD polyethylene wax for improving the surface properties of aqueous care products and polishes. It improves the buffability, increases filling capacity and produces an anti-slip effect. The above-mentioned properties are generated by mixing AQUACER 506 with polymers in a ratio of 3:1 (solid wax to solid polymer). A mixing ratio of 1:6 increases the water- and alcohol-resistance, the protection against heel marks (= foot traffic resistance), and the dirt-repellent action. AQUACER 506 is compatible with all known polymer dispersions and plasticizers. view less | |
AQUACER® 507 | BYK | AQUACER® 507 is an anionic emulsion of an oxidized HD polyethylene wax. It is suitable for use in non-ionic and anionic water-borne automotive systems and industrial paints. This product enhances flip-flop effect, improves the D.O.I. of clear coats, enhan...view more AQUACER® 507 is an anionic emulsion of an oxidized HD polyethylene wax. It is suitable for use in non-ionic and anionic water-borne automotive systems and industrial paints. This product enhances flip-flop effect, improves the D.O.I. of clear coats, enhances hardness and slip, and reduces short wave defects (mottling, Bénard cells). view less | |
AQUACER® 513 | BYK | AQUACER® 513 is a non-ionic emulsion based on an oxidized HD polyethylene wax. It is suitable for use in aqueous systems and printing inks. This product improves the following surface properties: scratch resistance in aqueous systems, rub resistance in pr...view more AQUACER® 513 is a non-ionic emulsion based on an oxidized HD polyethylene wax. It is suitable for use in aqueous systems and printing inks. This product improves the following surface properties: scratch resistance in aqueous systems, rub resistance in printing inks and black heel marking resistance in parquet lacquers. view less | |
AQUACER 519 | BYK | AQUACER 519 is an emulsion based on a HD polyethylene wax for improving the surface properties of aqueous care products and polishes. It improves the buffability, increases filling capacity and produces an anti-slip effect. The above-mentioned properties ...view more AQUACER 519 is an emulsion based on a HD polyethylene wax for improving the surface properties of aqueous care products and polishes. It improves the buffability, increases filling capacity and produces an anti-slip effect. The above-mentioned properties are generated by mixing AQUACER 519 with polymers in a ratio of 3:1 (solid wax to solid polymer). A mixing ratio of 1:6 increases the water- and alcohol-resistance, the protection against heel marks (= foot traffic resistance), and the dirt-repellent action. AQUACER 519 is compatible with all known polymer dispersions and plasticizers. view less | |
AQUACER® 526 | BYK | AQUACER® 526 is a wax emulsion for water-borne effect coatings. It is an emulsion of an anionic modified Ethylene-Vinyl Acetate-Copolymer wax (EVA). This product is suitable for water-borne top coats and base coats. It enhances flip-flop effect, improves ...view more AQUACER® 526 is a wax emulsion for water-borne effect coatings. It is an emulsion of an anionic modified Ethylene-Vinyl Acetate-Copolymer wax (EVA). This product is suitable for water-borne top coats and base coats. It enhances flip-flop effect, improves orientation of effect pigments (aluminum, mica, etc.), reduces short wave defects (mottling, Bénard cells), and there is no negative influence on chemical resistance. view less | |
AQUACER 527 | BYK | AQUACER 527 is a wax emulsion based on a modified EVA copolymer wax to improve surface characteristics in aqueous coating systems and printing inks. | |
AQUACER 528 | BYK | AQUACER 528 is an emulsion based on an ethylene-acrylic acid-copolymer wax for improving the surface properties of aqueous care products. It offers strong anti-slip effect and good foot traffic resistance. | |
AQUACER 530 | BYK | AQUACER 530 is a wax emulsion for improved surface characteristics in aqueous printing inks, overprint varnishes, wood and furniture coatings as well as inkjet inks. | |
AQUACER® 531 | BYK | AQUACER® 531is a wax emulsion for improving surface properties of water-borne industrial paints and printing inks. It is a non-ionic emulsion based on a modified polyethylene wax. This additive improves the following surface properties: slip, scratch resi...view more AQUACER® 531is a wax emulsion for improving surface properties of water-borne industrial paints and printing inks. It is a non-ionic emulsion based on a modified polyethylene wax. This additive improves the following surface properties: slip, scratch resistance, rub resistance and anti blocking. view less | |
AQUACER 532 | BYK | AQUACER 532 is an emulsion of a modified HD polyethylene wax for improved surface characteristics in aqueous coating systems. | |
AQUACER® 533 | BYK | AQUACER® 533 is a wax emulsion on the basis of modified paraffin for aqueous systems to improve surface slip, anti-blocking, and water-resistance. It is typically used in architectural coatings and in the printing inks industry. | |
AQUACER® 537 | BYK | AQUACER® 537 is an anionic emulsion based on a modified paraffin wax. It is suitable for aqueous systems for furniture- and parquet, industrial- and decorative paints. This product improves the following surface properties: water repellency, anti blocking...view more AQUACER® 537 is an anionic emulsion based on a modified paraffin wax. It is suitable for aqueous systems for furniture- and parquet, industrial- and decorative paints. This product improves the following surface properties: water repellency, anti blocking and slip. view less | |
AQUACER® 539 | BYK | AQUACER® 539 is a non-ionic emulsion based on a modified paraffin wax. This product is suitable for aqueous systems for furniture- and parquet, industrial- and decorative paints. It improves the following surface properties: slip, water repellency, anti b...view more AQUACER® 539 is a non-ionic emulsion based on a modified paraffin wax. This product is suitable for aqueous systems for furniture- and parquet, industrial- and decorative paints. It improves the following surface properties: slip, water repellency, anti blocking, scratch resistance, rub resistance and soft feel effect. view less | |
AQUACER 541 | BYK | AQUACER 541 is an aqueous emulsion of a montan ester wax for care products and polishes as well as for aqueous coating systems and leather coatings. | |
AQUACER® 552 | BYK | AQUACER® 552 is a non-ionic emulsion based on an oxidized HD polyethylene wax. This product is suitable for use in aqueous systems and printing inks. It is used to improve scratch resistance in aqueous systems. | |
AQUACER 561 | BYK | AQUACER 561 is a beeswax-based wax emulsion to improve surface protection in aqueous care products and coating systems. | |
AQUACER 565 | BYK | AQUACER 565 is an aqueous carnauba wax emulsion for improving the surface characteristics of care products, polishes, and leather coatings. It seals and thereby covers any minor scratches on the surface that is to be treated and restores the color of the ...view more AQUACER 565 is an aqueous carnauba wax emulsion for improving the surface characteristics of care products, polishes, and leather coatings. It seals and thereby covers any minor scratches on the surface that is to be treated and restores the color of the surface. The melting point of 85 °C means that the wax emulsion can easily be polished up using a soft terry cloth or microfiber cloth, but polishing with mechanical tools is also possible. view less | |
AQUACER 570 | BYK | AQUACER 570 is a modified Ecolabel-compliant sunflower wax emulsion to improve the surface properties of care products and polishes. It seals and thereby covers any minor scratches on the surface that is to be treated, and restores the surface’s original ...view more AQUACER 570 is a modified Ecolabel-compliant sunflower wax emulsion to improve the surface properties of care products and polishes. It seals and thereby covers any minor scratches on the surface that is to be treated, and restores the surface’s original color. It also improves the hydrophobicity and the oleophobicity of care products and polishes. This product is recommended for maintaining and protecting all types of surfaces, for leather, coated and uncoated surfaces. view less | |
AQUACER 571 | BYK | AQUACER 571 is a modified rice bran wax emulsion to improve the surface properties of care products, polishes, and aqueous coating systems. | |
AQUACER 581 | BYK | AQUACER 581 is a wax emulsion based on carnauba wax for aqueous paper coatings to improve surface slip, scratch-resistance, uniformity of printing ink acceptance, and ink setoff. Anti-caking additive for thermoplastics and hotmelts. | |
AQUACER 582 | BYK | AQUACER 582 is an emulsion based on a polyethylene wax for improving the surface properties of aqueous seed coatings. | |
AQUACER 583 | BYK | AQUACER 583 is a wax emulsion used to improve the surface characteristics of seed coatings. | |
AQUACER® 593 | BYK | AQUACER® 593 is a wax emulsion for improving anti slip of water-borne paint systems and printing inks. It is a non-ionic emulsion of a modified polypropylene wax. This product is suitable for use in non-ionic and anionic water-borne paint systems and prin...view more AQUACER® 593 is a wax emulsion for improving anti slip of water-borne paint systems and printing inks. It is a non-ionic emulsion of a modified polypropylene wax. This product is suitable for use in non-ionic and anionic water-borne paint systems and printing inks. view less | |
AQUACER 595 | BYK | AQUACER 595 is an emulsion based on a modified polypropylene wax for improving the surface properties of aqueous care products. It offers a strong anti-slip effect and good dirt repulsion. In aqueous leather finishes it produces an anti-slip and anti-tack...view more AQUACER 595 is an emulsion based on a modified polypropylene wax for improving the surface properties of aqueous care products. It offers a strong anti-slip effect and good dirt repulsion. In aqueous leather finishes it produces an anti-slip and anti-tack effect. view less | |
AQUACER 597 | BYK | AQUACER 597 is a cationic wax emulsion based on a modified polypropylene wax for formulating release agents for metal die casting. | |
AQUACER® 840 | BYK | AQUACER® 840 is a cationic emulsion of an oxidized HD polyethylene wax. This product is suitable for use in non-ionic and anionic water-borne automotive systems and industrial paints. It enhances flip-flop effect, improves the D.O.I. of clear coats, impro...view more AQUACER® 840 is a cationic emulsion of an oxidized HD polyethylene wax. This product is suitable for use in non-ionic and anionic water-borne automotive systems and industrial paints. It enhances flip-flop effect, improves the D.O.I. of clear coats, improves orientation of effect pigments and reduces short wave defects. view less | |
AQUAMAT® 208 | BYK | AQUAMAT® 208 is an oxidized HD polyethylene wax dispersion. It is suitable for aqueous systems e. g. furniture- and parquet lacquer, industrial- and decorative paints and inks. The additive improves the following surface properties: gloss reduction, scrat...view more AQUAMAT® 208 is an oxidized HD polyethylene wax dispersion. It is suitable for aqueous systems e. g. furniture- and parquet lacquer, industrial- and decorative paints and inks. The additive improves the following surface properties: gloss reduction, scratch resistance and soft feel effect. view less | |
AQUAMAT® 263 | BYK | AQUAMAT® 263 is an oxidized HD polyethylene wax dispersion. This product is suitable for aqueous systems e. g. furniture- and parquet lacquer, industrial- and decorative paints and inks. The additive improves the following surface properties: gloss reduct...view more AQUAMAT® 263 is an oxidized HD polyethylene wax dispersion. This product is suitable for aqueous systems e. g. furniture- and parquet lacquer, industrial- and decorative paints and inks. The additive improves the following surface properties: gloss reduction, scratch resistance, soft feel effect, rub resistance, anti blocking and black heel resistance. view less | |
AQUATIX® 8421 | BYK | AQUATIX® 8421 is a non-ionic emulsion of a modified Ethylene-Vinyl-Acetate (EVA) copolymer wax. It improves the rheological properties and brilliance of effect pigment slurries that are co-solvent-free. This product provides the following properties: impr...view more AQUATIX® 8421 is a non-ionic emulsion of a modified Ethylene-Vinyl-Acetate (EVA) copolymer wax. It improves the rheological properties and brilliance of effect pigment slurries that are co-solvent-free. This product provides the following properties: improves effect pigment orientation, reduces cloudiness /mottling, shows less sensivity to co-solvents in coating systems compared to PU based thickeners, is “ready to use”, provides easy handling and incorporation compared to clays or acrylic thickeners, and excellent anti-settling properties in coatings during storage and application. view less | |
BENTOLITE-L 10 | BYK | BENTOLITE-L 10 is a low iron rheology additive based on natural bentonite for aqueous plastic refractories. | |
BENTOLITE-L 3 | BYK | BENTOLITE-L 3 is a low iron rheology additive based on natural bentonite for aqueous plastic refractories. | |
BIOPOL BR 14 | Chemipol | BIOPOL BR 14 is a broad range in-can preservative based on BRONOPOL, specifically designed to avoid bacterial growth and damage caused by microorganisms in waterborne technical products. BIOPOL BR 14 is a cost-effective product with a broad range of activ...view more BIOPOL BR 14 is a broad range in-can preservative based on BRONOPOL, specifically designed to avoid bacterial growth and damage caused by microorganisms in waterborne technical products. BIOPOL BR 14 is a cost-effective product with a broad range of activity. The preservative product is suitable for plastic paints, fillers, emulsions, glues, adhesives, sealants, and detergents. BIOPOL BR 14 does not release formaldehyde. BIOPOL BR 14 is stable in a broad range of pH and temperatures. BIOPOL BR 14 is fully soluble in water and most of the polar solvents. view less | Request Sample |
BIOPOL BR 30 | Chemipol | BIOPOL BR 30 is a broad range in-can preservative based on BRONOPOL, specifically designed to avoid bacterial growth and damage caused by microorganisms in waterborne technical products. BIOPOL BR 14 is a cost-effective product with a broad range of activ...view more BIOPOL BR 30 is a broad range in-can preservative based on BRONOPOL, specifically designed to avoid bacterial growth and damage caused by microorganisms in waterborne technical products. BIOPOL BR 14 is a cost-effective product with a broad range of activity. The preservative product is suitable for plastic paints, fillers, emulsions, glues, adhesives, sealants, and detergents. BIOPOL BR 30 does not release formaldehyde. BIOPOL BR 30 is stable in a broad range of pH and temperatures. BIOPOL BR 30 is fully soluble in water and most of the polar solvents. view less | Request Sample |
BIOPOL BR 50 | Chemipol | BIOPOL BR 50 is a broad range in-can preservative based on CMIT/MIT and (Benzyloxy)Methanol, specifically designed to avoid bacterial growth and damage caused by microorganisms in waterborne technical products. Preservative product is suitable for plastic...view more BIOPOL BR 50 is a broad range in-can preservative based on CMIT/MIT and (Benzyloxy)Methanol, specifically designed to avoid bacterial growth and damage caused by microorganisms in waterborne technical products. Preservative product is suitable for plastic paints, fillers, emulsions, glues, adhesives, sealants, and detergents. BIOPOL BR 50 is a cost-effective preservative with a broad range of activity. BIOPOL BR 50 is an AOX & Formaldehyde free preservative. BIOPOL BR 50 is stable in a broad range of pH and temperatures. Especially appropriate for warm weather zones. view less | Request Sample |
BIOPOL C 15 | Chemipol | BIOPOL C 15 is a broad range in-can preservative based on CMIT/MIT adsorbed on Caolin, specifically designed to avoid bacterial growth and damage caused by microorganisms in waterborne technical products. Preservative product is suitable for plastic paint...view more BIOPOL C 15 is a broad range in-can preservative based on CMIT/MIT adsorbed on Caolin, specifically designed to avoid bacterial growth and damage caused by microorganisms in waterborne technical products. Preservative product is suitable for plastic paints, fillers, emulsions, glues, adhesives, sealants, and detergents. BIOPOL C 15 is formulated in powder form and it is AOX & VOC free. It is a formaldehyde free, cost-effective preservative. Especially appropriate for warm weather zones. As the preservative is water dispersible, it is not recommended for transparent products. view less | Request Sample |
BIOPOL FI 31 | Chemipol | BIOPOL FI 31 is a broad range in-can preservative based on CMIT/MIT and formaldehyde, specifically designed to avoid microbial growth and damage caused by microorganisms in waterborne technical products. BIOPOL FI 31 is a cost-effective preservative. Its ...view more BIOPOL FI 31 is a broad range in-can preservative based on CMIT/MIT and formaldehyde, specifically designed to avoid microbial growth and damage caused by microorganisms in waterborne technical products. BIOPOL FI 31 is a cost-effective preservative. Its balanced composition guarantees long-term preservation and quick biocidal action. The preservative product is suitable for plastic paints, fillers, emulsions, glues, adhesives, sealants, and detergents. BIOPOL FI 31 is stable in a broad range of pH and temperatures. view less | Request Sample |
BIOPOL IB 61 | Chemipol | BIOPOL IB 61 is a broad range in-can preservative based on CMIT/MIT and Bronopol, specifically designed to avoid microbial growth and damage caused by microorganisms in waterborne technical products. Preservative product suitable for plastic paints, fille...view more BIOPOL IB 61 is a broad range in-can preservative based on CMIT/MIT and Bronopol, specifically designed to avoid microbial growth and damage caused by microorganisms in waterborne technical products. Preservative product suitable for plastic paints, fillers, emulsions, glues, adhesives, sealants and detergents. VOC-free product. BIOPOL IB 61 balanced composition guarantees a long-term preservative action and a quick biocidal activity. BIOPOL IB 61 is stable in a broad range of pH and temperatures. Preservative especially well-suited form warm weather zones. view less | Request Sample |
BIOPOL ITS | Chemipol | BIOPOL ITS is a broad range in-can preservative based on CMIT/MIT, specifically designed to avoid microbial growth and damage caused by microorganisms in waterborne technical products. Preservative product suitable for plastic paints, fillers, emulsions, ...view more BIOPOL ITS is a broad range in-can preservative based on CMIT/MIT, specifically designed to avoid microbial growth and damage caused by microorganisms in waterborne technical products. Preservative product suitable for plastic paints, fillers, emulsions, glues, adhesives, sealants, and detergents. BIOPOL ITS is VOC & AOX & Formaldehyde free preservative. BIOPOL ITS has a broad range of activity and top stability under high temperatures, until 50ºC. view less | Request Sample |
BIOPOL JL 101R | Chemipol | BIOPOL JL 101R is a broad range in-can preservative based on O-formal, specifically designed to avoid microbial growth and damage caused by microorganisms in waterborne technical products. Preservative product suitable for plastic paints, fillers, emulsio...view more BIOPOL JL 101R is a broad range in-can preservative based on O-formal, specifically designed to avoid microbial growth and damage caused by microorganisms in waterborne technical products. Preservative product suitable for plastic paints, fillers, emulsions, glues, adhesives, sealants, and detergents. BIOPOL JL 101R is a cost-effective preservative with fast biocidal activity. BIOPOL JL 101R is effective throughout a wide range of pH and temperatures. CMIT/MIT free preservative. Preservatives are especially appropriate for warm weather zones. view less | Request Sample |
BIOPOL JL 75 | Chemipol | BIOPOL JL 75 is a broad range in-can preservative based on N-formal, specifically designed to avoid microbial growth and damage caused by microorganisms in waterborne technical products. Preservative product suitable for plastic paints, fillers, emulsions...view more BIOPOL JL 75 is a broad range in-can preservative based on N-formal, specifically designed to avoid microbial growth and damage caused by microorganisms in waterborne technical products. Preservative product suitable for plastic paints, fillers, emulsions, glues, adhesives, sealants, and detergents. BIOPOL JL 75 is a cost-effective preservative with fast biocidal activity. BIOPOL JL 75 is effective throughout a wide range of pH and temperatures. view less | Request Sample |
BIOPOL JM 140L | Chemipol | BIOPOL JM 140L is a broad range in-can preservative based on CMIT/MIT and O-formal, specifically designed to avoid microbial growth and damage caused by microorganisms in waterborne technical products. BIOPOL JM 140L is a cost-effective preservative with ...view more BIOPOL JM 140L is a broad range in-can preservative based on CMIT/MIT and O-formal, specifically designed to avoid microbial growth and damage caused by microorganisms in waterborne technical products. BIOPOL JM 140L is a cost-effective preservative with excellent protection of the vapor phase. Preservative product is suitable for plastic paints, fillers, emulsions, glues, adhesives, sealants and detergents. BIOPOL JM 140L is stable in a broad range of pH and temperatures. Especially well-suited form warm weather zones. view less | Request Sample |
BIOPOL JM 15 | Chemipol | BIOPOL JM 15 is a broad range in-can preservative based on CMIT/MIT and O-formal, specifically designed to avoid microbial growth and damage caused by microorganisms in waterborne technical products. BIOPOL JM 15 is a cost-effective preservative with exce...view more BIOPOL JM 15 is a broad range in-can preservative based on CMIT/MIT and O-formal, specifically designed to avoid microbial growth and damage caused by microorganisms in waterborne technical products. BIOPOL JM 15 is a cost-effective preservative with excellent protection of the vapor phase. Preservative product is suitable for plastic paints, fillers, emulsions, glues, adhesives, sealants and detergents. BIOPOL JM 15 is stable in a broad range of pH and temperatures. Preservatives are especially well-suited for warm weather zones view less | Request Sample |
BIOPOL JM 29 | Chemipol | BIOPOL JM 29 is a broad range in-can preservative based on CMIT/MIT and O-formal, specifically designed to avoid microbial growth and damage caused by microorganisms in waterborne technical products. BIOPOL JM 29 is a cost-effective preservative. BIOPOL J...view more BIOPOL JM 29 is a broad range in-can preservative based on CMIT/MIT and O-formal, specifically designed to avoid microbial growth and damage caused by microorganisms in waterborne technical products. BIOPOL JM 29 is a cost-effective preservative. BIOPOL JM 29 balanced composition guarantees long-term preservation and a quick biocidal action. Preservative product suitable for plastic paints, fillers, emulsions, glues, adhesives, sealants, and detergents. BIOPOL JM JM 29 is stable in a broad range of pH and temperatures. Preservatives specially well-suited form warm weather zones. view less | Request Sample |
BIOPOL K14 | Chemipol | BIOPOL K14 is a non-oxidizing biocidal product based on CMIT/MIT, specifically designed to avoid microbial growth and damage caused by microorganisms in waterborne technical products. Preservative product suitable for plastic paints, fillers, emulsions, g...view more BIOPOL K14 is a non-oxidizing biocidal product based on CMIT/MIT, specifically designed to avoid microbial growth and damage caused by microorganisms in waterborne technical products. Preservative product suitable for plastic paints, fillers, emulsions, glues, adhesives, sealants, and detergents. AOX, VOC, CMR, and Formaldehyde free preservatives. Cost-effective product. BIOPOL K14 is stable in a broad range of pH and temperatures. Excellent solution for formaldehyde-sensible products. view less | Request Sample |
BIOPOL KB | Chemipol | BIOPOL KB is a broad range of in-can preservatives based on CMIT/MIT and BIT, specifically designed to avoid microbial growth and damage caused by microorganisms in waterborne technical products. Preservative product is suitable for plastic paints, filler...view more BIOPOL KB is a broad range of in-can preservatives based on CMIT/MIT and BIT, specifically designed to avoid microbial growth and damage caused by microorganisms in waterborne technical products. Preservative product is suitable for plastic paints, fillers, emulsions, glues, adhesives, sealants, and detergents. AOX & Formaldehyde free preservative. Cost-effective product. BIOPOL KB balanced composition guarantees long-term preservation without skin sensitization (H317) labeling. BIOPOL KB is stable in a broad range of pH and temperatures. Preservative especially appropriate for formaldehyde-sensible products. view less | Request Sample |
BIOPOL KBB | Chemipol | BIOPOL KBB is a broad range of in-can preservatives based on CMIT/MIT, BIT, and BRONOPOL, specifically designed to avoid microbial growth and damage caused by microorganisms in waterborne technical products. The preservative product is suitable for plasti...view more BIOPOL KBB is a broad range of in-can preservatives based on CMIT/MIT, BIT, and BRONOPOL, specifically designed to avoid microbial growth and damage caused by microorganisms in waterborne technical products. The preservative product is suitable for plastic paints, fillers, emulsions, glues, adhesives, sealants, and detergents. AOX & Formaldehyde free preservative. BIOPOL KBB balanced composition guarantees long-term preservation without skin sensitization (H317) labeling. BIOPOL KBB is stable in a broad range of pH and temperatures. Preservatives are especially appropriate for formaldehyde-sensible products. view less | Request Sample |
BIOPOL KBJ | Chemipol | BIOPOL KBJ is a broad range of in-can preservatives based on CMIT/MIT, BIT, and BRONOPOL, specifically designed to avoid microbial growth and damage caused by microorganisms in waterborne technical products. Preservative products suitable for plastic pain...view more BIOPOL KBJ is a broad range of in-can preservatives based on CMIT/MIT, BIT, and BRONOPOL, specifically designed to avoid microbial growth and damage caused by microorganisms in waterborne technical products. Preservative products suitable for plastic paints, fillers, emulsions, glues, adhesives, sealants, and detergents. AOX & Formaldehyde free preservative. Cost-effective preservative. BIOPOL KBJ balanced composition guarantees long-term preservation without skin sensitization (EUH208) labeling. BIOPOL KBJ is stable in a broad range of pH and temperatures. Especially appropriate for formaldehyde-sensible products. view less | Request Sample |
BIOPOL KF 15 | Chemipol | BIOPOL KF 15 is a broad range in-can preservative based on OIT and O-formal, specifically designed to avoid microbial growth and damage caused by microorganisms in waterborne technical products. Preservative product is suitable for plastic paints, fillers...view more BIOPOL KF 15 is a broad range in-can preservative based on OIT and O-formal, specifically designed to avoid microbial growth and damage caused by microorganisms in waterborne technical products. Preservative product is suitable for plastic paints, fillers, emulsions, glues, adhesives, sealants, and detergents. BIOPOL KF 15 balanced composition guarantees long-term preservation and a quick biocidal action. BIOPOL KF 15 is a cost-effective preservative that requires a low dosage. Preservatives are especially well-suited for warm weather zones. view less | Request Sample |
BIOPOL KF 78 | Chemipol | BIOPOL KF 78 is a broad range in-can preservative based on OIT and O-formal, specifically designed to avoid microbial growth and damage caused by microorganisms in waterborne technical products. Preservative products suitable for plastic paints, fillers, ...view more BIOPOL KF 78 is a broad range in-can preservative based on OIT and O-formal, specifically designed to avoid microbial growth and damage caused by microorganisms in waterborne technical products. Preservative products suitable for plastic paints, fillers, emulsions, glues, adhesives, sealants, and detergents. BIOPOL KF 78 balanced composition guarantees long-term preservation and a quick biocidal action. BIOPOL KF 78 is a cost-effective preservative that requires a low dosage. Preservative especially well-suited for warm weather zones. view less | Request Sample |
BIOPOL MSO 35 | Chemipol | BIOPOL MSO 35 is a broad range in-can preservative based on CMIT/MIT and N-formal, specifically designed to avoid microbial growth and damage caused by microorganisms in waterborne technical products. Preservative products suitable for plastic paints, fil...view more BIOPOL MSO 35 is a broad range in-can preservative based on CMIT/MIT and N-formal, specifically designed to avoid microbial growth and damage caused by microorganisms in waterborne technical products. Preservative products suitable for plastic paints, fillers, emulsions, glues, adhesives, sealants, and detergents. BIOPOL MSO 35 balanced composition guarantees long-term preservation and a quick biocidal action. BIOPOL MSO 35 is excellent to protect the vapor phase of the product. BIOPOL MSO 35 is stable in a broad range of pH and temperatures. view less | Request Sample |
BIOPOL MSO 40 | Chemipol | BIOPOL MSO 40 is a broad range in-can preservative based on CMIT/MIT and formaldehyde donor, specifically designed to avoid microbial growth and damage caused by microorganisms in waterborne technical products. Preservative product is suitable for plastic...view more BIOPOL MSO 40 is a broad range in-can preservative based on CMIT/MIT and formaldehyde donor, specifically designed to avoid microbial growth and damage caused by microorganisms in waterborne technical products. Preservative product is suitable for plastic paints, fillers, emulsions, glues, adhesives, sealants, and detergents. BIOPOL MSO 40 balanced composition guarantees a long-term preservation and a quick biocidal action. BIOPOL MSO 40 has a reduced skin sensitization potential. BIOPOL MSO 40 is stable in a broad range of pH and temperatures. view less | Request Sample |
BIOPOL PK 5 | Chemipol | BIOPOL PK 5 is a broad range, solid in-can preservative based on CMIT/MIT and Bronopol adsorbed on Silica, specifically designed to avoid microbial growth and damage caused by microorganisms in waterborne technical products. The preservative product is s...view more BIOPOL PK 5 is a broad range, solid in-can preservative based on CMIT/MIT and Bronopol adsorbed on Silica, specifically designed to avoid microbial growth and damage caused by microorganisms in waterborne technical products. The preservative product is suitable for plastic paints, fillers, emulsions, glues, adhesives, sealants, and detergents. BIOPOL PK 5 is VOC & AOX free preservative. Its balanced composition guarantees long-term preservation and quick biocidal action. Dust free view less | Request Sample |
BIOPOL TC 3 | Chemipol | BIOPOL TC 3 is a broad range in-can preservative based on CMIT/MIT, specifically designed to avoid microbial growth and damage caused by microorganisms in waterborne technical products. Preservative product suitable for plastic paints, fillers, emulsions,...view more BIOPOL TC 3 is a broad range in-can preservative based on CMIT/MIT, specifically designed to avoid microbial growth and damage caused by microorganisms in waterborne technical products. Preservative product suitable for plastic paints, fillers, emulsions, glues, adhesives, sealants, and detergents. BIOPOL TC 3 is an AOX & VOC free preservative. BIOPOL TC 3 is free of formaldehyde. Its balanced composition guarantees a long-term preservative action. BIOPOL TC 3 is stable in a broad range of pH and temperatures. Especially appropriate for formaldehyde-sensible products. view less | Request Sample |
BIOPOL TI 158 | Chemipol | BIOPOL TI 158 is a broad range in-can preservative based on CMIT/MIT and O-formal, specifically designed to avoid microbial growth and damage caused by microorganisms in waterborne technical products. The preservative product is suitable for plastic paint...view more BIOPOL TI 158 is a broad range in-can preservative based on CMIT/MIT and O-formal, specifically designed to avoid microbial growth and damage caused by microorganisms in waterborne technical products. The preservative product is suitable for plastic paints, fillers, emulsions, glues, adhesives, sealants, and detergents. BIOPOL TI 158 is a cost-effective preservative with excellent protection of vapor phase. Its balanced composition guarantees a long-term preservative action. BIOPOL TI 158 is stable in a broad range of pH and temperatures. view less | Request Sample |
BIOPOL TRC 150 | Chemipol | BIOPOL TRC 150 is a broad-range, solid in-can preservative based on MIT and BIT adsorbed in kaolin, specifically designed to avoid microbial growth and damage caused by microorganisms in technical products such as ceramics, glazes, or any aqueous suspensi...view more BIOPOL TRC 150 is a broad-range, solid in-can preservative based on MIT and BIT adsorbed in kaolin, specifically designed to avoid microbial growth and damage caused by microorganisms in technical products such as ceramics, glazes, or any aqueous suspension susceptible to colonized by bacteria. BIOPOL TRC 150 balanced composition guarantees a long-term preservation action. BIOPOL TRC 150 is a cost-effective preservative effective in a broad range of pH and temperatures. view less | Request Sample |
BIOPOL VR 20 | Chemipol | BIOPOL VR 20 is a broad range in-can preservative based on BIT, specifically designed to avoid microbial growth and damage caused by microorganisms in waterborne technical products. Preservative product suitable for plastic paints, fillers, emulsions, glu...view more BIOPOL VR 20 is a broad range in-can preservative based on BIT, specifically designed to avoid microbial growth and damage caused by microorganisms in waterborne technical products. Preservative product suitable for plastic paints, fillers, emulsions, glues, adhesives, sealants, and detergents. AOX, VOC, CMIT/MIT, and Formaldehyde free preservatives. Cost-effective product. BIOPOL VR 20 balanced composition guarantees a long-term preservation action. BIOPOL VR 20 is stable in a broad range of pH and temperatures. Preservative especially appropriate for formaldehyde-sensible products view less | Request Sample |
BIOPOL XM | Chemipol | BIOPOL XM is a broad range in-can preservative based on MIT and BIT, specifically designed to avoid microbial growth and damage caused by microorganisms in waterborne technical products. Preservative product suitable for plastic paints, fillers, emulsions...view more BIOPOL XM is a broad range in-can preservative based on MIT and BIT, specifically designed to avoid microbial growth and damage caused by microorganisms in waterborne technical products. Preservative product suitable for plastic paints, fillers, emulsions, glues, adhesives, sealants, and detergents. AOX & VOC & Formaldehyde free preservative. Cost-effective preservatives are effective throughout a wide range of pH, from 2 to 10. BIOPOL XM balanced composition guarantees a long-term preservation action. Preservatives are especially appropriate for formaldehyde-sensible products. view less | Request Sample |
BIOPOL XMD 5050 | Chemipol | BIOPOL XMD 5050 is a broad range in-can preservative based on MIT/BIT and Bronopol, specifically designed to avoid microbial growth and damage caused by microorganisms in waterborne technical products. Preservative product suitable for plastic paints, fil...view more BIOPOL XMD 5050 is a broad range in-can preservative based on MIT/BIT and Bronopol, specifically designed to avoid microbial growth and damage caused by microorganisms in waterborne technical products. Preservative product suitable for plastic paints, fillers, emulsions, glues, adhesives, sealants and detergents. BIOPOL XMD 5050 is an AOX & VOC free preservative. BIOPOL XMD 5050 is effective throughout a wide range of pH, from 2 to 10. BIOPOL XMD 5050 is stable in a broad range of pH and temperatures. Preservative specially well-suited for warm weather zones. view less | Request Sample |
BIOPOL XMO 210 | Chemipol | BIOPOL XMO 210 is a broad range in-can preservative based on MIT and BIT, specifically designed to avoid microbial growth and damage caused by microorganisms in waterborne technical products. Preservative product is suitable for plastic paints, fillers, e...view more BIOPOL XMO 210 is a broad range in-can preservative based on MIT and BIT, specifically designed to avoid microbial growth and damage caused by microorganisms in waterborne technical products. Preservative product is suitable for plastic paints, fillers, emulsions, glues, adhesives, sealants, and detergents. AOX & VOC & Formaldehyde free preservative. Cost-effective preservatives effective throughout a wide range of pH, from 2 to 10. BIOPOL XMO 210 balanced composition guarantees a long-term preservation action. BIOPOL XMO 210 is stable in a broad range of pH and temperatures. Specially appropriate for formaldehyde-sensible products. view less | Request Sample |
BYK-011 | BYK | BYK-011 is a silicone-free, polymer-based defoamer for aqueous coating systems (also radiation curable systems). It is particularly recommended for two pack polyurethane systems and offers very good recoatability. | |
BYK®-012 | BYK | BYK®-012 is a compound of foam-destroying polymers and hydrophobic particles. This product is especially suitable for defoaming emulsion paints and plasters with a PVC-range of 30-85, where it prevents foam during production and application. The product i...view more BYK®-012 is a compound of foam-destroying polymers and hydrophobic particles. This product is especially suitable for defoaming emulsion paints and plasters with a PVC-range of 30-85, where it prevents foam during production and application. The product is silicone- and mineral oil-free and is specifically recommended for VOC-free systems. The additive shows optimum efficiency at low dosage, is acid and alkaline resistant and can be used in a pH-range of 3 - 12. The product may lead to turbidity and seeding in clear coats. view less | |
BYK®-014 | BYK | BYK®-014 is a mixture of foam-destroying polymers, fat derivatives and hydrophobic particles. This product shows excellent defoaming properties in various emulsion types such as acrylates, styrene acrylics or VAE´s (vinyl acetate ethylene). It is especial...view more BYK®-014 is a mixture of foam-destroying polymers, fat derivatives and hydrophobic particles. This product shows excellent defoaming properties in various emulsion types such as acrylates, styrene acrylics or VAE´s (vinyl acetate ethylene). It is especially suitable for defoaming emulsion paints and plasters with a PVC range of 30-85. The product is silicone-free and mineral oil-free and is specifically recommended for VOC-free systems. The additive shows optimum efficiency at low dosage, is acid and alkaline resistant, and can be used in a pH range of 3 - 12. view less | |
BYK-015 | BYK | BYK-015 is a silicone-free, polymer-based defoamer with anti-popping properties for aqueous coatings. Particularly recommended for automotive and industrial coatings. | |
BYK®-016 | BYK | BYK®-016 is a compound of foam-destroying polymers and hydrophobic particles. It is a very effective silicone- and mineral oil free defoamer. It has no negative influence on the printing behavior and does not cause defects in the typography. At the time o...view more BYK®-016 is a compound of foam-destroying polymers and hydrophobic particles. It is a very effective silicone- and mineral oil free defoamer. It has no negative influence on the printing behavior and does not cause defects in the typography. At the time of publication the active compound in BYK-016 fully meets all requirements of the European Union for "materials and articles in contact with foodstuffs“, and complies with FDA 21 CFR § 175.105, 175.300, 175.320, 176.200, 176.210. view less | |
BYK®-017 | BYK | BYK®-017 is a compound of foam destroying polysiloxanes and hydrophobic solids. It is especially suited for defoaming millbases during dispersion and subsequent processing. The product is an excellent defoamer for glycol pastes and aqueous pigment concent...view more BYK®-017 is a compound of foam destroying polysiloxanes and hydrophobic solids. It is especially suited for defoaming millbases during dispersion and subsequent processing. The product is an excellent defoamer for glycol pastes and aqueous pigment concentrates. It exhibits excellent defoaming during grinding and excellent storage stability. This results in improved grinding and handling of the final pigment concentrates and coatings. view less | |
BYK®-018 | BYK | BYK®-018 is a mixture of hydrophobic solids and foam destroying polysiloxanes. It is especially suitable for pigmented emulsion systems based on styrene/ acrylate, acrylate or acrylate/polyurethane combinations with a low PVC. In industrial emulsion paint...view more BYK®-018 is a mixture of hydrophobic solids and foam destroying polysiloxanes. It is especially suitable for pigmented emulsion systems based on styrene/ acrylate, acrylate or acrylate/polyurethane combinations with a low PVC. In industrial emulsion paints that are applied by dipping, flow coating, and airless spraying BYK-018 is very efficient against microfoam. view less | |
BYK®-019 | BYK | BYK®-019 is a solution of a polyether modified polydimethylsiloxane. BYK-019 is recommended for aqueous coatings based on polyurethane dispersions and polyurethane /acrylic combinations. It is also effective for defoaming pigment concentrate formulations....view more BYK®-019 is a solution of a polyether modified polydimethylsiloxane. BYK-019 is recommended for aqueous coatings based on polyurethane dispersions and polyurethane /acrylic combinations. It is also effective for defoaming pigment concentrate formulations. To reduce microfoam, a combination of BYK-019 with BYK-024 in a ratio of 3:2 has been shown to give excellent results. view less | |
BYK®-021 | BYK | BYK®-021 is a mixture of foam destroying polysiloxanes and hydrophobic solids in polyglycol. It is particularly useful for pigmented emulsions based on styrene/acrylics, acrylics or acrylic/polyurethanes with PVC‘s of 18-25%. This defoamer has demonstrate...view more BYK®-021 is a mixture of foam destroying polysiloxanes and hydrophobic solids in polyglycol. It is particularly useful for pigmented emulsions based on styrene/acrylics, acrylics or acrylic/polyurethanes with PVC‘s of 18-25%. This defoamer has demonstrated high activity against microfoam in high gloss and semi-gloss aqueous coatings, specifically in airless and air-assisted spray applied coatings. view less | |
BYK®-022 | BYK | BYK®-022 is a mixture of foam destroying polysiloxanes and hydrophobic solids in polyglycol. It is especially suited for pigmented emulsion systems based on styrene/acrylics, acrylics or acrylic/polyurethanes with PVC‘s of 18-25%. It can also be used in a...view more BYK®-022 is a mixture of foam destroying polysiloxanes and hydrophobic solids in polyglycol. It is especially suited for pigmented emulsion systems based on styrene/acrylics, acrylics or acrylic/polyurethanes with PVC‘s of 18-25%. It can also be used in amine-neutralized systems and is very efficient against microfoam. view less | |
BYK®-023 | BYK | BYK®-023 is an emulsion of foam destroying polysiloxanes, hydrophobic solids and emulsifiers. This product is preferably used in pigmented emulsion paints with PVC‘s of 30-50% based on styrene/acrylics, acrylic or terpolymer binders. It also can be used i...view more BYK®-023 is an emulsion of foam destroying polysiloxanes, hydrophobic solids and emulsifiers. This product is preferably used in pigmented emulsion paints with PVC‘s of 30-50% based on styrene/acrylics, acrylic or terpolymer binders. It also can be used in hybrid systems. view less | |
BYK®-024 | BYK | BYK®-024 is a mixture of foam destroying polysiloxanes and hydrophobic solids in polyglycol. This product is suited for emulsion systems with PVC‘s from 0 to 25% based on polyurethane and acrylic/polyurethane. It is especially useful in rolling, brushing ...view more BYK®-024 is a mixture of foam destroying polysiloxanes and hydrophobic solids in polyglycol. This product is suited for emulsion systems with PVC‘s from 0 to 25% based on polyurethane and acrylic/polyurethane. It is especially useful in rolling, brushing or spraying applications. view less | |
BYK®-025 | BYK | BYK®-025 is a solution of foam destroying polysiloxanes. It is highly recommended for non-pigmented polyurethane and acrylic/ polyurethane emulsion systems. This defoamer is very easily incorporated and allows optimizing dosage by post-addition while the ...view more BYK®-025 is a solution of foam destroying polysiloxanes. It is highly recommended for non-pigmented polyurethane and acrylic/ polyurethane emulsion systems. This defoamer is very easily incorporated and allows optimizing dosage by post-addition while the paint is running on a curtain coater. view less | |
BYK®-028 | BYK | BYK®-028 is a mixture of foam destroying polysiloxanes and hydrophobic solids in polyglycol. This product is the standard defoamer for water-based systems and the basis (starting selection) for the testing of a defoamer series. BYK-028 is suitable for dis...view more BYK®-028 is a mixture of foam destroying polysiloxanes and hydrophobic solids in polyglycol. This product is the standard defoamer for water-based systems and the basis (starting selection) for the testing of a defoamer series. BYK-028 is suitable for dispersion paints with a PVC from 0 to 25 based on acrylate/polyurethane or polyurethane. BYK-028 is easy to incorporate. view less | |
BYK®-035 | BYK | BYK®-035 is a mixture of paraffin based mineral oils and hydrophobic components, containing silicone. This product is especially suitable for emulsion systems with a PVC of 20-40. Its effectiveness is not impaired by high shear forces. | |
BYK®-037 | BYK | BYK®-037 is an emulsion of paraffin based mineral oils and hydrophobic components, containing silicone. It is used in all emulsion paints and plasters as well as for defoaming during the dispersion production. BYK-037 is very cost-efficient. | |
BYK®-038 | BYK | BYK®-038 is a mixture of paraffin based mineral oils and hydrophobic components, containing silicone. This product is especially designed for universal use in APEO-free emulsions. It contains a small amount of a paint compatible silicone which enhances ex...view more BYK®-038 is a mixture of paraffin based mineral oils and hydrophobic components, containing silicone. This product is especially designed for universal use in APEO-free emulsions. It contains a small amount of a paint compatible silicone which enhances excellent efficiency. BYK-038 should be preferably used in emulsion systems with a PVC from 20 to 70. view less | |
BYK-039 | BYK | BYK-039 is a mineral oil-based, VOC- and silicone-free defoamer for aqueous emulsion systems within a PVC range of 35-70. Does not contain alkylphenol ethoxylates. Also suitable for high-solid PUR leather coatings. | |
BYK®-044 | BYK | BYK®-044 is an emulsion of hydrophobic particles and polysiloxanes. It is especially suitable for defoaming of the millbase during dispersion and further processing. The product defoams excellently glycol pastes and aqueous pigment concentrates. For defoa...view more BYK®-044 is an emulsion of hydrophobic particles and polysiloxanes. It is especially suitable for defoaming of the millbase during dispersion and further processing. The product defoams excellently glycol pastes and aqueous pigment concentrates. For defoaming of emulsion paints and dispersions lacquers BYK-044 is preferably used in pure acrylic and styrene acrylic emulsions. view less | |
BYK®-054 | BYK | BYK®-054 is especially suited for solvent-free systems like PUR and epoxy floorings. It eliminates air-bubbles and ensures pinhole-free surfaces. Due to its strong incompatibility, the additive‘s influence on the transparency of clear systems must be eval...view more BYK®-054 is especially suited for solvent-free systems like PUR and epoxy floorings. It eliminates air-bubbles and ensures pinhole-free surfaces. Due to its strong incompatibility, the additive‘s influence on the transparency of clear systems must be evaluated. BYK-054 is also suitable to defoam plastisols. view less |