| BRB Siloen® WA 264 | BRB International BV | BRB Siloen® WA 264 is a polyether-modified siloxane. It is a silicone surfactant for aqueous coatings with excellent wetting and levelling properties. | |
| BYK®-302 | BYK | BYK®-302 is a polyether modified polydimethylsiloxane. This product is a solvent-free version of BYK-300. This product is especially used in systems in which solvent-free additives are requested or where a requirement for a special solvent exists. | |
| BYK®-307 | BYK | BYK®-307 is a polyether modified polydimethylsiloxane. This product has features similar to BYK-306. Due to the fact that it is solvent-free, it is preferred in systems where solvent-free additives are requested or where a requirement for a special solven...view more BYK®-307 is a polyether modified polydimethylsiloxane. This product has features similar to BYK-306. Due to the fact that it is solvent-free, it is preferred in systems where solvent-free additives are requested or where a requirement for a special solvent exists. view less | |
| BYK®-310 | BYK | BYK®-310 is a solution of a polyester modified polydimethylsiloxane. This product is a heat resistant silicone additive, i.e., in contrast to conventional (polyether modified) silicones, it shows no thermal decomposition at temperatures between 150°C/302°...view more BYK®-310 is a solution of a polyester modified polydimethylsiloxane. This product is a heat resistant silicone additive, i.e., in contrast to conventional (polyether modified) silicones, it shows no thermal decomposition at temperatures between 150°C/302°F and 230°C/446°F. Thus, upon the recoating baking systems, no loss in adhesion and no surface defects occur. (Note: The aforementioned defects can be caused by the decomposition products of conventional silicones at temperatures above 150°C/302°F.) The effective substance of BYK-310 is listed in title 21 CFR (food and drugs) § 175.300, Indirect Food Additives, Adhesives and Components of Coatings. The usage level may not exceed 0,1% (delivery form based on total formulation) and the film thickness may not exceed 12 µm. view less | |
| BYK®-331 | BYK | BYK®-331 is a polyether modified polydimethylsiloxane. This product is used in all solvent-borne, solvent-free and aqueous coatings. In two-component polyurethane systems, it can also be added to the isocyanate hardener. | |
| BYK®-333 | BYK | BYK®-333 is a polyether modified polydimethylsiloxane. This product strongly increases surface slip and considerably improves substrate wetting. It can be used universally in all coatings systems. In aqueous systems, it increases anti-blocking properties....view more BYK®-333 is a polyether modified polydimethylsiloxane. This product strongly increases surface slip and considerably improves substrate wetting. It can be used universally in all coatings systems. In aqueous systems, it increases anti-blocking properties. BYK-333 displays excellent compatibility and can be used as an anti-cratering additive. view less | |
| BYK®-370 | BYK | BYK®-370 is a reactive silicone surface additive that is a solution of a polyester modified hydroxy functional polydimethylsiloxane. This product reacts via its primary OH-groups with the binder and is preferably used in solvent-borne two-pack polyurethan...view more BYK®-370 is a reactive silicone surface additive that is a solution of a polyester modified hydroxy functional polydimethylsiloxane. This product reacts via its primary OH-groups with the binder and is preferably used in solvent-borne two-pack polyurethanes. It can also crosslink with the following binder systems: alkyd/melamine, polyester/melamine, acrylic/melamine, self-crosslinking acrylates, and epoxies. BYK-370 increases the surface slip. view less | |
| BYK®-377 | BYK | BYK®-377 is a polyether modified polydimethylsiloxane. The product improves substrate wetting and leveling at low dosages. In most cases only half the amount of a conventional silicone is needed to optimize substrate wetting, slip and tape release of UV c...view more BYK®-377 is a polyether modified polydimethylsiloxane. The product improves substrate wetting and leveling at low dosages. In most cases only half the amount of a conventional silicone is needed to optimize substrate wetting, slip and tape release of UV curable, 2 pack PU, polyester/melamine and aqueous topcoats. Due to the good compatibility in common binder systems, the production of highly transparent varnishes is possible. Typically it does not cause turbidity in clearcoats. Sanding is required for recoat adhesion. The OH groups of BYK-377 can react with polyisocyanates view less | |
| COATOSIL* 1220 SURFACTANT | Momentive | CoatOSil 1220 surfactant is a non-fluorine based organomodified siloxane surfactant with the Description unique superwetting properties in waterborne coatings for spray applications, high-speed roll applications and hard-to-wet surfaces. It can also impro...view more CoatOSil 1220 surfactant is a non-fluorine based organomodified siloxane surfactant with the Description unique superwetting properties in waterborne coatings for spray applications, high-speed roll applications and hard-to-wet surfaces. It can also improve flow and leveling properties, while remaining stable in aqueous formulations having pH 6-11. CoatOSil 1220 surfactant solutions typically provide spread areas more than 100 times greater than the corresponding volume drop of pure water, and 2 view less | |
| Dynasylan® F 8815 | Evonik Operations GmbH, BL Silanes | Dynasylan® F 8815 is a fluoroalkylfunctional water-borne oligosiloxane which acts as an oleophobic surface modification agent on oxidic, carboxy- and hydroxyfunctional substrates for example ceramic or natural fibers like cotton or leather. | |
| Hydropalat® 140 | BASF Formulation Additives | Hydropalat® 140 is a low-foam flow promoter and substrate wetting agent for aqueous paints and coatings is based on organo modified polysiloxane. compared with substrate wetting agents based on other chemicals, such as block copolymers (Hydropalat® 110, 1...view more Hydropalat® 140 is a low-foam flow promoter and substrate wetting agent for aqueous paints and coatings is based on organo modified polysiloxane. compared with substrate wetting agents based on other chemicals, such as block copolymers (Hydropalat® 110, 130), sulfosuccinates (Hydropalat® 875) or acetylene diol derivatives, Hydropalat® 140 brings about a much greater reduction in static interfacial tension. Even when it is present in a concentration of 0.5%, values much lower than 25 mN/m can be achieved. view less | |
| TEGO® Twin 4100 | Evonik Operations GmbH, BL Coating Additives | TEGO® Twin 4100 is a highly effective siloxane-based gemini surfactant. It is a clear to hazy liquid. The haziness of the liquid has no affect on the product's properties. TEGO® Twin 4100 has excellent substrate wetting and anti-crater effects for wood an...view more TEGO® Twin 4100 is a highly effective siloxane-based gemini surfactant. It is a clear to hazy liquid. The haziness of the liquid has no affect on the product's properties. TEGO® Twin 4100 has excellent substrate wetting and anti-crater effects for wood and furniture coatings, industrial coatings, printing inks, overprint varnishes, and polymer emulsions. It has good long-term persistance and no foam stabilization. view less | Request Sample |
