| EXOCOAT™ 151A | Axcentive Sarl | EXOCOAT® 151A by Axcentive is a photocatalytic nano-titanium oxide sol with a strong self-cleaning performance. The photocatalytic effect results in effective radical formation which breaks down organic matter like dirt and soil. Airborne particles like V...view more EXOCOAT® 151A by Axcentive is a photocatalytic nano-titanium oxide sol with a strong self-cleaning performance. The photocatalytic effect results in effective radical formation which breaks down organic matter like dirt and soil. Airborne particles like VOCs, NOx, and biopollution are also eradicated by EXOCOAT® 151A. It can be used as a general air purifier. Though most effective in outdoor light conditions, it is adapted for use under visible light as found in the interior. In all cases, it should be used as a topcoat to ensure its full effect. Glass and walls coated with EXOCOAT® 151A are super hydrophilic enhancing water-sheeting, also called the wash-off effect. It may be used on other flat surfaces such as plastics or coated substrates yet only interior. It dries under room temperature conditions. Spray application is recommended to reach thin monolayers which prove to be more effective. It is listed with EINECS. TSCA, AICS, and CEPA. view less | |
| EXOCOAT™ 151B | Axcentive Sarl | EXOCOAT® 151B by Axcentive is a photocatalytic nano-titanium oxide sol with a strong self-cleaning performance. The photocatalytic effect results in effective radical formation which breaks down organic matter like dirt and soil. Airborne particles like V...view more EXOCOAT® 151B by Axcentive is a photocatalytic nano-titanium oxide sol with a strong self-cleaning performance. The photocatalytic effect results in effective radical formation which breaks down organic matter like dirt and soil. Airborne particles like VOCs, NOx, and biopollution are also eradicated by EXOCOAT® 151B. In all cases, it should be used as a topcoat to ensure its full effect. EXOCOAT® 151B coated walls are super hydrophilic enhancing water-sheeting, also called the wash-off effect. It is targeted for porous substrates like concrete, brickwork, and gypsum. It is not meant for glass substrates. It dries under room temperature conditions. Brush, roller, or Spray application is recommended to reach homogeneous coatings. It is listed with EINECS. TSCA, AICS, and CEPA. view less | |
| Ferric Chloride Anhydrous | Qingdao Sun Chemical Corporation Limited | Ferric Chloride Anhydrous is mainly used for the engraving etching of electronic circuit board or purify drink water and treat waste water. It is also used to make other iron salts, oxidant, catalyst, mordant and ink. In addition, it is used in constructi...view more Ferric Chloride Anhydrous is mainly used for the engraving etching of electronic circuit board or purify drink water and treat waste water. It is also used to make other iron salts, oxidant, catalyst, mordant and ink. In addition, it is used in construction field. This product is a brown crystal with a molecular weight of 162.21, an insoluble substance content of 96.0%. view less | |
| INSOCAT BTP 11 | LEHVOSS Group | INSOCAT BTP 11 is a highly reactive Organic Titanate. It is soluble in many organic solvents and is supplied with hundred percent active content. It is extremely sensitive to moisture and is widely used as a catalyst for reactions such as Esterification, ...view more INSOCAT BTP 11 is a highly reactive Organic Titanate. It is soluble in many organic solvents and is supplied with hundred percent active content. It is extremely sensitive to moisture and is widely used as a catalyst for reactions such as Esterification, Trans-Esterification, and Olefin Polymerisation. It is recommended as a cross linking agent for wire enamels, surface coatings, and printing inks. It is also used as a surface modifier, adhesion promoter, wax and oil additives, and in the manufacture of scratch resistant glass. view less | |
| K-CURE® 1040 | King Industries, Inc. | K-CURE® 1040 is a solution of para-Toluenesulfonic acid (p-TSA) in isoproanol, featuring high gloss, excellent weathering characteristics, outstanding exterior durability, and fast curing properties. Common applications include can, paper, and wood coatin...view more K-CURE® 1040 is a solution of para-Toluenesulfonic acid (p-TSA) in isoproanol, featuring high gloss, excellent weathering characteristics, outstanding exterior durability, and fast curing properties. Common applications include can, paper, and wood coatings, appliance finishes, and printing inks. view less | |
| K-CURE® 1040W | King Industries, Inc. | K-CURE® 1040W is a good quality para-Toluenesulfonic acid (p-TSA) stimulant that is dissolved in water. Some advantages of this product include fast curing ability, good weather ability, it is non-flammable, high gloss, and it is integraded into water sys...view more K-CURE® 1040W is a good quality para-Toluenesulfonic acid (p-TSA) stimulant that is dissolved in water. Some advantages of this product include fast curing ability, good weather ability, it is non-flammable, high gloss, and it is integraded into water systems. It is soluble in water, alcohol, and also glycols. This product can be applied to water based wood coatings, paper coatings, and printing inks. view less | |
| K-CURE® 129B | King Industries, Inc. | K-CURE® 129B is a strong acid stimulant supplied at 50% in a blend of alcohols. It is a strong acid stimulant that is made to give fast cures with good pot life in two component acid curing lacquers. K-CURE® 129B is not recommended to be used on metal sub...view more K-CURE® 129B is a strong acid stimulant supplied at 50% in a blend of alcohols. It is a strong acid stimulant that is made to give fast cures with good pot life in two component acid curing lacquers. K-CURE® 129B is not recommended to be used on metal substrates because of its corrosive nature. This product offer fast curing, and high acid value which allows lower does levels. This is a product that is soluble in water, alcohol, and glycols. It can be applied to wood, paper, and plastic coatings. view less | |
| K-KAT® 348 | King Industries, Inc. | K-KAT® 348 is an adaptable bismuth carboxylate stimulant that is made for blocked isocyanate and two standard urethane coatings. It can provide similar characteristics to basic tin catalysts without the environmental setbacks. This product appears as a cl...view more K-KAT® 348 is an adaptable bismuth carboxylate stimulant that is made for blocked isocyanate and two standard urethane coatings. It can provide similar characteristics to basic tin catalysts without the environmental setbacks. This product appears as a clear, straw liquid and offers great catalysis of secondary hydroxyls, gloss retention, exterior durability, and the ability to be used in ambient, force dry, and bake systems. It is soluble in glycol ethers, aliphatics, and aromatics. It is limited in solubility in alcohols and esters and is insoluble in water. K-KAT® 348 can be applied in 2K and blocked isocyanate coatings, urethane elastomers, foams and coatings, and cationic coatings. view less | |
| K-KAT® 4205 | King Industries, Inc. | K-KAT® 4205 is a zirconium chelate complex that is an effective stimulant for high solids 2-integral urethane coatings. It is effective for ambient and low temperature cure systems. This product appears as a clear, colorless liquid and offers fast tack fr...view more K-KAT® 4205 is a zirconium chelate complex that is an effective stimulant for high solids 2-integral urethane coatings. It is effective for ambient and low temperature cure systems. This product appears as a clear, colorless liquid and offers fast tack free time along with good viscosity stability. It is effective at low metal concentrations and also effective with a mix of isocyanates and polycols. K-KAT® 4205 is soluble in ketones, aromatic hydrocarbons, and esters. It can be applied to automotive topcoats, maintenance coatings, structural plastics coatings, and aerospace coatings. view less | |
| K-KAT® 5218 | King Industries, Inc. | K-KAT® 5218 is an aluminum chelate complex stimulant for 2 basic urethane coatings. It is effective for both ambient cure and baked systems. K-KAT® 5218 is supplied in a reactive diluent for high solids applications. It offers pot life extension with the ...view more K-KAT® 5218 is an aluminum chelate complex stimulant for 2 basic urethane coatings. It is effective for both ambient cure and baked systems. K-KAT® 5218 is supplied in a reactive diluent for high solids applications. It offers pot life extension with the addition of 2,4-pentanedione, fast tack free time, exterior durability, and is effective with a variety of isocyanates and polyols. It appears as a slightly hazy, amber liquid and can be applied in automotive topcoats, aerospace coatings, maintenance coatings, and coatings for structural plastics. This product is soluble in ketones, esters, glycol ethers, alcohols, and aromatic hydrocarbons. view less | |
| K-KAT® 6212 | King Industries, Inc. | K-KAT® 6212 appears as a clear, straw liquid and is an effective stimulant when isocyanate and hydroxyl groups react with each other. It is a zirconium chelate complex dissolved in a reactive diluent. It offers good cure response and exterior durability a...view more K-KAT® 6212 appears as a clear, straw liquid and is an effective stimulant when isocyanate and hydroxyl groups react with each other. It is a zirconium chelate complex dissolved in a reactive diluent. It offers good cure response and exterior durability along with a short tack free time. This product doesn't add to the hydrolysis of polyester resins and high selectivity for NCO/OH reactions over NCO/water reaction. It is soluble in esters, alcohols, ketones, aliphatic and aromatic hydrocarbons, glycol ethers, and glycol ether acetates. It is only partially soluble in water. It can be applied to adhesives, polyurethane coatings, casting resins and polyurethane resin synthesis, RIM, and water-based two component coatings. view less | |
| K-KAT® 670 | King Industries, Inc. | K-KAT® 670 is a novel non-tin stimulant for products containing crosslinkable silane terminated polymers. It appears as a light amber liquid and is soluble in esters, ketones, aromatic hydrocarbons, alcohols, and is insoluble in water. This product can be...view more K-KAT® 670 is a novel non-tin stimulant for products containing crosslinkable silane terminated polymers. It appears as a light amber liquid and is soluble in esters, ketones, aromatic hydrocarbons, alcohols, and is insoluble in water. This product can be applied in ambient cured 1 component organosilane and 2 component organosilane hybrid coatings, caulks, adhesives, elastomers, and sealants. view less | |
| K-KAT® XC-B221 | King Industries, Inc. | K-KAT® XC-B221 is an experimental bismuth carboxylate stimulant that is made for blocked isocyanate and two basic urethane coatings. It is a bismuth stimulant that can contribute similar qualities to standard tin stimulants without the environmental drawb...view more K-KAT® XC-B221 is an experimental bismuth carboxylate stimulant that is made for blocked isocyanate and two basic urethane coatings. It is a bismuth stimulant that can contribute similar qualities to standard tin stimulants without the environmental drawbacks. This product offers good glass retention, exterior durability, and the ability to be used in ambient, force dry, and bake systems. K-KAT® XC-B221 is soluble in butanol, ethanol, methanol, isopropanol, glycol ethers, glycol ether acetates, aliphatic and aromatic hydrocarbons, and is insoluble in water. This product appears as a clear, straw liquid and can be applied in 2K, blocked isocyanate coatings, urethane elastomers, foams, coatings, and cationic electro-coatings. view less | |
| K-KAT® XK-614 | King Industries, Inc. | K-KAT® XK-614 is a non-tin stimulant that is suggested to be applied in 2-component solvent-borne, 2-component waterborne polyurethanes, and also for 1-component blocked isocyanate systems. It is easy to add to the polyol components and offers good curing...view more K-KAT® XK-614 is a non-tin stimulant that is suggested to be applied in 2-component solvent-borne, 2-component waterborne polyurethanes, and also for 1-component blocked isocyanate systems. It is easy to add to the polyol components and offers good curing time qualities. It also has good hydrolytic stability and exterior durability. This product has non-yellowing ability and great gloss retention characteristics. It appears as a light, yellow liquid, is soluble in alcohols, and is insoluble in water. view less | |
| K-KAT® XK-617 | King Industries, Inc. | K-KAT® XK-617 is an effective stimulant when isocyanates and polyols used in the production of cast elastomers react with each other. It is a proprietary blended organometallic complex specifically formulated to be a substitute to mercury stimulant withou...view more K-KAT® XK-617 is an effective stimulant when isocyanates and polyols used in the production of cast elastomers react with each other. It is a proprietary blended organometallic complex specifically formulated to be a substitute to mercury stimulant without the concern of toxicity. It appears as a pale, light amber liquid, offers good cure response, and is environmentally more acceptable. This product is soluble in glycol ethers, n-butanol, ketones, aliphatics. aromatics, and is partially soluble in water. It is normally applied in 2K urethanes for cast elastomers. view less | |
| K-KAT® XK-628 | King Industries, Inc. | K-KAT® XK-628 is an adaptable bismuth carboxylate stimulant that is made for blocked isocyanate and two fundamental urethane coatings. It can provide similar characteristics to basic tin stimulants without the environmental drawbacks. K-KAT® XK-628 appear...view more K-KAT® XK-628 is an adaptable bismuth carboxylate stimulant that is made for blocked isocyanate and two fundamental urethane coatings. It can provide similar characteristics to basic tin stimulants without the environmental drawbacks. K-KAT® XK-628 appears as a clear, amber liquid and is a made to give enhanced hydrolytic stability. This product offers good exterior ability, gloss retention, and the ability to be used in ambient, force dry, and bake systems. It is soluble in glycol ethers, aliphatics, and aromatics. It is partially soluble in alcohols, esters, and is insoluble in water. This product can be applied in 2K and blocked isocyanate coatings, urethane elastomers, foams, and coatings. view less | |
| K-KAT® XK-635 | King Industries, Inc. | K-KAT® XK-635 is a new non-tin stimulant suggested for solvent based or solvent free 2-component polyurethanes and 1-component blocked isocyanate systems. This product appears as a light, yellow liquid and offers good pot life in 2K PU systems, good cure ...view more K-KAT® XK-635 is a new non-tin stimulant suggested for solvent based or solvent free 2-component polyurethanes and 1-component blocked isocyanate systems. This product appears as a light, yellow liquid and offers good pot life in 2K PU systems, good cure time, non-yellowing, and gloss retention. It is soluble in esters, aromatic hydrocarbons, and ketones. It is insoluble in water. This product is 100% active, weighs 9.5 lbs per gallon, and has a specific gravity of 1.14 g/ml. view less | |
| K-KAT® XK-639 | King Industries, Inc. | K-KAT® XK-639 is a new non-tin stimulant suggested for solvent based or solvent free 2-component polyurethanes and 1-component blocked isocyanate systems. This product appears as a light, yellow liquid and offers good pot life in 2K PU systems, good cure ...view more K-KAT® XK-639 is a new non-tin stimulant suggested for solvent based or solvent free 2-component polyurethanes and 1-component blocked isocyanate systems. This product appears as a light, yellow liquid and offers good pot life in 2K PU systems, good cure time, non-yellowing, and gloss retention. It is soluble in esters, aromatic hydrocarbons, and ketones. It is insoluble in water. This product is 50% active in isopropanol, weighs 7.6 lbs per gallon, and has a specific gravity of 0.91 g/ml. view less | |
| K-KAT® XK-640 | King Industries, Inc. | K-KAT® XK-640 is an adaptable bismuth carboxylate stimulant that is made for blocked isocyanate and two component urethane coatings. It offers good exterior durability, good gloss retention, and similar properties to standard tin catalysts without the env...view more K-KAT® XK-640 is an adaptable bismuth carboxylate stimulant that is made for blocked isocyanate and two component urethane coatings. It offers good exterior durability, good gloss retention, and similar properties to standard tin catalysts without the environmental drawbacks. K-KAT® XK-640 is a designed to provide improved hydrolytic stability compared to other bismuth carboxylate catalysts. This product is soluble in glycol ethers, aliphatics, and aromatics, has partial solubility in alcohols and esters, and is insoluble in water. It appears as a clear, amber liquid, is 18% metal, and can be applied in ambient, force dry and bake systems, 2K and blocked isocyanate coatings, and in the production of urethane coatings. view less | |
| K-KAT® XK-651 | King Industries, Inc. | K-KAT® XK-651 is an adaptable bismuth carboxylate stimulant that is made for blocked isocyanate, two component urethanes, and one and two component silane terminated coatings. K-KAT® XK-651 is made to give good hydrolytic stability. This product has good ...view more K-KAT® XK-651 is an adaptable bismuth carboxylate stimulant that is made for blocked isocyanate, two component urethanes, and one and two component silane terminated coatings. K-KAT® XK-651 is made to give good hydrolytic stability. This product has good gloss retention, exterior durability, can replace tin stimulants, and good solubility. It is soluble in glycol ethers, aliphatics, aromatics, has partial solubility in alcohols and esters, and is not soluble in water. It can be applied in 2K and blocked isocyanate coatings, and in the production of urethane elastomers, foams, and coatings. view less | |
| K-PURE® CXC-1612 | King Industries, Inc. | K-PURE® CXC-1612 is an antimony hexafluoride based catalyst that is for thermal initiated cationic polymerization. It appears as an off white powder and offers viscosity stability, cure response, and solubility. This product can be applied in PWB, conform...view more K-PURE® CXC-1612 is an antimony hexafluoride based catalyst that is for thermal initiated cationic polymerization. It appears as an off white powder and offers viscosity stability, cure response, and solubility. This product can be applied in PWB, conformal coatings, cleaners & strippers, and adhesives & sealants. view less | |
| K-PURE® CXC-1615 | King Industries, Inc. | K-PURE® CXC-1615 is an amine salt of trifluoromethanesulfonic acid that is suggested to be used in thermal initiated cationic polymerization of cycloaliphatic epoxies, epoxy esters and epoxy ether resins. It also functions as a stimulant for condensation ...view more K-PURE® CXC-1615 is an amine salt of trifluoromethanesulfonic acid that is suggested to be used in thermal initiated cationic polymerization of cycloaliphatic epoxies, epoxy esters and epoxy ether resins. It also functions as a stimulant for condensation reactions with amino resins and benzoxazine resins. It appears as an amber liquid and is 60% active. This product is soluble in alcohols, water, glycols, glycol ethers, ketones, and carbonates. It is not soluble in aliphatic and aromatic hydrocarbons. view less | |
| K-PURE® CXC-1765 | King Industries, Inc. | K-PURE® CXC-1765 is a zinc complex stimulantt for cross linking of epoxy/carboxylic and epoxy/anhydride functional resins. K-PURE® CXC-1765 catalyzes the reaction of glycidyl ether, ester, cycloaliphatic epoxies and epoxidized oils with carboxyl and anhyd...view more K-PURE® CXC-1765 is a zinc complex stimulantt for cross linking of epoxy/carboxylic and epoxy/anhydride functional resins. K-PURE® CXC-1765 catalyzes the reaction of glycidyl ether, ester, cycloaliphatic epoxies and epoxidized oils with carboxyl and anhydride groups. K-PURE® CXC-1765 offers enhances storage stability, thermal stability, and low color relative to amine catalyzed formulations. view less | |
| K-PURE® TAG-2172 | King Industries, Inc. | K-PURE® TAG-2172 is an amine blocked Dodecylbenzenesulfonic acid (DDBSA) that is used as a thermal acid generator. Usual activation ranges from 140°C to 190°C depending upon the circumstances of the formation and application. This product appears as a cle...view more K-PURE® TAG-2172 is an amine blocked Dodecylbenzenesulfonic acid (DDBSA) that is used as a thermal acid generator. Usual activation ranges from 140°C to 190°C depending upon the circumstances of the formation and application. This product appears as a clear, light color liquid and offers viscosity stability, broad solubility, and low trace metals. It is soluble in alcohols, water, glycols, glycol ethers, esters, aliphatic & aromatic hydrocarbons, and ketones. view less | |
| K-PURE® TAG-2678 | King Industries, Inc. | K-PURE® TAG-2678 is a quaternary ammonium blocked triflic acid thermal acid generator specifically made to be used in thermally cured microlithography coatings. It has a sharp activation profile and does not provide any volatile components when activated....view more K-PURE® TAG-2678 is a quaternary ammonium blocked triflic acid thermal acid generator specifically made to be used in thermally cured microlithography coatings. It has a sharp activation profile and does not provide any volatile components when activated. K-PURE® TAG-2678 is ideally appropriate for amino crosslinkable melamine, self-condensed melamine, glycoluril, urea or silanol and alkoxysilane crosslinkable resins. K-PURE® TAG-2678 can also be used to stimulize the polymerization of epoxy resins and ring opening polymerization of cyclic ethers as well as other monomers capable of undergoing cationic polymerization. This product appears as white crystals and is soluble in PGME, ethyl lactate, acetone, and propylene carbonate. It has limited solubility in PGMEA and is almost insoluble in water. view less | |
| K-PURE® TAG-2713 | King Industries, Inc. | K-PURE® TAG-2713 is a semiconductor grade amine blocked thermal acid generator made to be used in microlithography coatings. Its activation range is between 120°C and 140°C depending upon time, formulation components and film thickness. K-PURE® TAG-2713 i...view more K-PURE® TAG-2713 is a semiconductor grade amine blocked thermal acid generator made to be used in microlithography coatings. Its activation range is between 120°C and 140°C depending upon time, formulation components and film thickness. K-PURE® TAG-2713 is ideally appropriate as a stimulant for amino cross-linkable melamine, self-condensed melamine, glycoluril, urea, or silanol and alkoxysilane cross-linkable resins. KPURE ® TAG-2713 can also be used in any lithography application where the rapid and selective generation of a strong acid is needed. This product appears as a clear solution and is soluble in ethyl lactate, water, and butanol. It is only partially soluble in PGMEA. view less | |
| Ketjenflex® CP | Axcentive Sarl | Ketjenflex® CP is a para toluene sulfonic acid in the form of a white crystalline powder. It is used as a strong protonating catalyst. Ketjenflex® CP can be used in acid cured wood coatings. | |
| KOSMOS® T 100 | Evonik Operations GmbH, BL Comfort & Insulation | KOSMOS® T 100 is the strongest gel catalyst particularly suitable for fast curing applications such as spray coatings and RIM. | |
| KOSMOS® T 12 N | Evonik Operations GmbH, BL Comfort & Insulation | KOSMOS® T 12 N is a dibutyltin dilaurate. Strong gel catalyst. Moderate hydrolytic stability. | |
| KRONOClean® 7000 | Kronos International, Inc. | KRONOClean® 7000 is a photocatalyst displaying not only activity in UV radiation, but also pronounced photoactivity in visible light. It is suitable for use in applications for eliminating unwanted odours (e.g. kitchen smells) and soiling on surfaces (e....view more KRONOClean® 7000 is a photocatalyst displaying not only activity in UV radiation, but also pronounced photoactivity in visible light. It is suitable for use in applications for eliminating unwanted odours (e.g. kitchen smells) and soiling on surfaces (e.g. nicotine), for air purification (amines, aldehydes, nitrogen oxides, mercaptans, etc.) and for improving room air quality (interior paints) in conjunction with paper, plastic films, window profiles, fibres, etc. view less | |
| KRONOClean® 7050 | Kronos International, Inc. | KRONOClean® 7050 is a photocatalyst designed for use in conjunction with UV radiation. It is suitable for eliminating unwanted odours (e.g. vehicle emissions) and soiling on surfaces (e.g. soot), for air purification (nitrogen oxides, sulphoxides, chlorin...view more KRONOClean® 7050 is a photocatalyst designed for use in conjunction with UV radiation. It is suitable for eliminating unwanted odours (e.g. vehicle emissions) and soiling on surfaces (e.g. soot), for air purification (nitrogen oxides, sulphoxides, chlorinated hydrocarbons, etc.) and for improving air quality (exterior paints) in conjunction with plastic films, window profiles, paints, fibres, etc. view less | |
| Lithium Neodecanoate (EGECat Li 2%) | EGE Kimya San ve Tic A.S. | Lithium Neodecanoate (EGECat Li 2%) is an esterification catalyst that is often used as a light coloured polyester. This product is soluble in organic solvents, and it has a lithium metal content of 2% and a total solids content of 63%. | |
| Luna-add K C404 | DKSH | Luna-add K C404 is a masterbatch of a catalyst for carboxyl / epoxy reaction in saturated carboxylated polyester. Active content: 10%. It is use as catalyst for the formulation of interior and exterior protective thermosetting powder coatings, HYBRID, TGI...view more Luna-add K C404 is a masterbatch of a catalyst for carboxyl / epoxy reaction in saturated carboxylated polyester. Active content: 10%. It is use as catalyst for the formulation of interior and exterior protective thermosetting powder coatings, HYBRID, TGIC or cured with glycidylesters. view less | Request Sample |
| Luna-add K C405-SD | DKSH | Luna-add K C405-SD is a masterbatch of a catalyst for carboxyl / epoxy reaction in superdurable saturated carboxylated polyester resin. Active content: 5%. It is use as catalyst for the formulation of exterior protective thermosetting powder coatings, cur...view more Luna-add K C405-SD is a masterbatch of a catalyst for carboxyl / epoxy reaction in superdurable saturated carboxylated polyester resin. Active content: 5%. It is use as catalyst for the formulation of exterior protective thermosetting powder coatings, cured with TGIC or with glycidylesters. view less | Request Sample |
| Mixed Chromium Phosphate | McGean-Rohco, Inc. | Mixed Chromium Phosphate is a clear, green solution. Uses include conversion coatings, corrosion inhibitors, catalysts and synthesis. | |
| Monomer SM6226 | Jiangsu Sanmu Group Corporation | Monomer SM6226 is a special tertiary acrylate used as a reactive amine synergist. | |
| Monomer SM6338 | Jiangsu Sanmu Group Corporation | Monomer SM6338 is a special tertiary acrylate used as a reactive amine synergist. | |
| NACURE® 1051 | King Industries, Inc. | NACURE® 1051 is a hydrophobic acid stimulant that is based on dinonylnaphthalene sulfonic acid supplied at 50% active in 2-Butoxyethanol. It is an oil soluble sulfonic acid that provides humidity resistance in high bake amino and phenolic systems. | |
| NACURE® 1323 | King Industries, Inc. | NACURE® 1323 is a hydrophobic amine neutralized Dinonylnaphthalenesulfonic acid (DNNSA) stimulant. It has been created to give maximum solubility, package stability and electrical resistance. Since DNNSA is a weaker acid than DNNDSA, it is more applicable...view more NACURE® 1323 is a hydrophobic amine neutralized Dinonylnaphthalenesulfonic acid (DNNSA) stimulant. It has been created to give maximum solubility, package stability and electrical resistance. Since DNNSA is a weaker acid than DNNDSA, it is more applicable for higher cure temperature applications. This product is soluble in alcohol, water, glycol ethers, and esters. It can be applied in coil coatings, electrostatic spray, electrocoating, and general industrials. view less | |
| NACURE® 1419 | King Industries, Inc. | NACURE® 1419 is a covalently blocked Dinonylnaphthalenesulfonic acid (DNNSA) stimulant. The polymeric moiety stays in the system and is capable of responding with the crosslinking agent. It offers low conductivity, good salt spray properties and adhesion,...view more NACURE® 1419 is a covalently blocked Dinonylnaphthalenesulfonic acid (DNNSA) stimulant. The polymeric moiety stays in the system and is capable of responding with the crosslinking agent. It offers low conductivity, good salt spray properties and adhesion, and is hardly affected by pigment absorption. This product is not soluble in water. It can be applied in electrostatic spray, can coatings, coil coatings, electrocoat, and metal decorating. This product appears as a clear and dark liquid. view less | |
| NACURE® 155 | King Industries, Inc. | NACURE® 155 is a hydrophobic sulfonic acid catalyst featuring excellent water, salt, and detergent resistance, superior adhesion, and low conductivity. It is primarily used as a catalyst in the curing of hydroxy, carboxy, and amide functional polymers wit...view more NACURE® 155 is a hydrophobic sulfonic acid catalyst featuring excellent water, salt, and detergent resistance, superior adhesion, and low conductivity. It is primarily used as a catalyst in the curing of hydroxy, carboxy, and amide functional polymers with melamine and urea-formaldehyde crosslinking agents. Common applications include waterborne can coatings, automotive primers, printing inks, electrocoatings, coil coatings, and appliance finishes. view less | |
| NACURE® 1557 | King Industries, Inc. | NACURE® 1557 appears as a clear and dark liquid. It is an amine blocked Dinonylnaphthalenesulfonic acid (DNNSA) stimulant uniquely made for decreased blistering in thicker films that are cured at higher temperatures. This product erases solvent popping in...view more NACURE® 1557 appears as a clear and dark liquid. It is an amine blocked Dinonylnaphthalenesulfonic acid (DNNSA) stimulant uniquely made for decreased blistering in thicker films that are cured at higher temperatures. This product erases solvent popping in high bake thick films and offers low conductivity, excellent humidity, and detergent resistance. It is soluble in alcohol, glycols, esters, glycol ethers, ketones, aromatic and aliphatic hydrocarbons. It is not soluble in water. It can be applied to things such as electrostatic spray, general industrials, can coatings, coil coatings, and appliance finishes. view less | |
| NACURE® 1953 | King Industries, Inc. | NACURE® 1953 is an amine blocked DNNSA stimulant and appears as a clear amber liquid. This is a product that is made to be applied in higher bake amino crosslinked systems like metal decorating, coil coatings and can also be applied in things such as elec...view more NACURE® 1953 is an amine blocked DNNSA stimulant and appears as a clear amber liquid. This is a product that is made to be applied in higher bake amino crosslinked systems like metal decorating, coil coatings and can also be applied in things such as electrocoating and appliance finishes. This product is resistant to detergent, overbake, humidity, and offers great flow and leveling, along with good solubility in organic solvents. NACURE® 1953 is soluble in aliphatic and aromatic hydrocarbons, alcohol, ketones, esters, glycol ethers and is insoluble in water. view less | |
| NACURE® 2107 | King Industries, Inc. | NACURE® 2107 appears as a clear, straw liquid and is an amine counterbalanced para-Toluenesulfonic (p-TSA) stimulant that is made for fast cure response. It improves metal scratch resistance of acid catalyzed formulations and offers waterborne or high sol...view more NACURE® 2107 appears as a clear, straw liquid and is an amine counterbalanced para-Toluenesulfonic (p-TSA) stimulant that is made for fast cure response. It improves metal scratch resistance of acid catalyzed formulations and offers waterborne or high solids coatings. This product can be applied to general industrials, appliance finishes, and coil coatings. It is soluble in alcohols, ethers, water, and glycols, partially soluble in ketones and aromatic hydrocarbons, and insoluble in aliphatic hydrocarbons. view less | |
| NACURE® 2500 | King Industries, Inc. | NACURE® 2500 is an amine neutralized p-Toluenesulfonic acid (p-TSA) stimulant that appears as a clear, straw liquid and is made for low temperature curing and maximum viscosity stability. It offers good cure response, exterior durability, and waterborne o...view more NACURE® 2500 is an amine neutralized p-Toluenesulfonic acid (p-TSA) stimulant that appears as a clear, straw liquid and is made for low temperature curing and maximum viscosity stability. It offers good cure response, exterior durability, and waterborne or high solids coatings. This product is soluble in alcohols, glycol ethers, glycols, and water, partially soluble in ketones, and insoluble in aliphatic and aromatic hydrocarbons. It can be applied in general industrials, appliance finishes, automotive topcoats, and coil coatings. view less | |
| NACURE® 2501 | King Industries, Inc. | NACURE® 2501 is an amine blocked Toluenesulfonic acid (TSA) stimulant that has been made for higher electrical resistivity and appears as a clear, straw liquid. It can be applied in electrostatic spray coatings, automotive topcoats, General industrials, a...view more NACURE® 2501 is an amine blocked Toluenesulfonic acid (TSA) stimulant that has been made for higher electrical resistivity and appears as a clear, straw liquid. It can be applied in electrostatic spray coatings, automotive topcoats, General industrials, and coil coatings. This product is soluble in alcohols, glycol ethers, glycols, esters, aromatic hydrocarbons, and especially ketones. It is insoluble in water and aliphatic hydrocarbons. view less | |
| NACURE® 2530 | King Industries, Inc. | NACURE® 2530 is an amine neutralized p-Toluenesulfonic acid (p-TSA) stimulant and appears as a clear, straw liquid. It has a low pH which allows for faster cure and reduces the potential of wrinkling from volatile amines, particularly at cure temperatures...view more NACURE® 2530 is an amine neutralized p-Toluenesulfonic acid (p-TSA) stimulant and appears as a clear, straw liquid. It has a low pH which allows for faster cure and reduces the potential of wrinkling from volatile amines, particularly at cure temperatures of 121° C (250° F) or higher. This product can be applied in appliance finishes, coil coatings, can coatings, wood coatings, paper coatings, automotive topcoats, and general industrials. It is soluble in alcohols, esters, glycols, glycol ethers, and water. It is partially soluble in ketones and insoluble in aliphatic and aromatic hydrocarbons. view less | |
| NACURE® 2547 | King Industries, Inc. | NACURE® 2547 appears as a clear, transparent liquid and is an amine blocked para -Toluenesulfonic acid (p-TSA) stimulant that is diluted with water for easier incorporation into water-based systems. It offers good cure response and viscosity stability and...view more NACURE® 2547 appears as a clear, transparent liquid and is an amine blocked para -Toluenesulfonic acid (p-TSA) stimulant that is diluted with water for easier incorporation into water-based systems. It offers good cure response and viscosity stability and is usually applied in water-based general industrials. This product is soluble in alcohols, glycols, water, glycol ethers and it is insoluble in ketones, esters, aromatic and aliphatic hydrocarbons. view less | |
| NACURE® 2558 | King Industries, Inc. | NACURE® 2558 is a partially amine counterbalanced para-Toluenesulfonic acid (p-TSA) stimulant that appears as a clear, straw liquid. It mixes a higher boiling solvent with a higher temperature dissociating amine to create a stimulant that is especially ef...view more NACURE® 2558 is a partially amine counterbalanced para-Toluenesulfonic acid (p-TSA) stimulant that appears as a clear, straw liquid. It mixes a higher boiling solvent with a higher temperature dissociating amine to create a stimulant that is especially effective in controlling wrinkling, popping and blistering in high solids coatings. It is soluble in alcohols, water, glycols, glycol ethers, and is insoluble in aliphatic and aromatic hydrocarbons, esters, and ketones. This product can be applied in automotive finishes, waterborne coatings, coil coatings, and general industrials. view less | |
| NACURE® 3327 | King Industries, Inc. | NACURE® 3327 appears as a clear transparent dark liquid. It is an amine neutralized Dinonylnaphthalenedisulfonic acid (DNNDSA) stimulant that has been created to provide enganced solubility when compared to other amine blocked DNNDSA stimulants. NACURE 33...view more NACURE® 3327 appears as a clear transparent dark liquid. It is an amine neutralized Dinonylnaphthalenedisulfonic acid (DNNDSA) stimulant that has been created to provide enganced solubility when compared to other amine blocked DNNDSA stimulants. NACURE 3327 offers a combination of package stability and cure response. This product has good adhesion, solubility, and corrosion resistance. It is applied to metal decorating coil coatings. electrostatic spray, and general industrials. It is soluble in alcohol, water, glycols, and glycol ethers. view less | |
| NACURE® 3525 | King Industries, Inc. | NACURE® 3525 appears as a clear transparent amber liquid. It is an amine neutralized Dinonylnaphthalenedisulfonic acid (DNNDSA) stimulant that uses a slower releasing amine for higher bake temperatures. NACURE® 3525 is formed for increased solubility, esp...view more NACURE® 3525 appears as a clear transparent amber liquid. It is an amine neutralized Dinonylnaphthalenedisulfonic acid (DNNDSA) stimulant that uses a slower releasing amine for higher bake temperatures. NACURE® 3525 is formed for increased solubility, especially in high solids polyester and alkyd formulations. It offers good ahesion, salt spray and water resistance, and no wrinkling. It is soluble in water, alcohol, glycol ethers, ketones, and glycols. It is usually applied in metal decorating, automotive topcoats, coil coatings, can coatings, appliance finishes, general industrials, and electrostatic spray. view less | |
| NACURE® 4000 | King Industries, Inc. | NACURE® 4000 appears as a clear and transparent light straw liquid. It is an alkyl acid phosphate stimulant. It is a weak acid catalyst recommended for use with high-NH/polymeric melamines and phenolic crosslinkers. It offers broad solubility in glycols, ...view more NACURE® 4000 appears as a clear and transparent light straw liquid. It is an alkyl acid phosphate stimulant. It is a weak acid catalyst recommended for use with high-NH/polymeric melamines and phenolic crosslinkers. It offers broad solubility in glycols, ethers, ketones, and also aromatic and water hydrocarbons. This product can be applied to general industrials, wood coatings, and plastic coatings. view less | |
| NACURE® 4054 | King Industries, Inc. | NACURE® 4054 is a hydrophobic alkyl acid phosphate stimulant supplied at 50% active in isobutanol. It is a weak acid stimulant that is recommended to be used with high -NH/polymeric melamines and phenolic crosslinkers. This product offers great solubility...view more NACURE® 4054 is a hydrophobic alkyl acid phosphate stimulant supplied at 50% active in isobutanol. It is a weak acid stimulant that is recommended to be used with high -NH/polymeric melamines and phenolic crosslinkers. This product offers great solubility, adhesion, and water resistance. It is designed to be applied to things such as, appliance finishes, topcoats, primers, and wood finishes. view less | |
| NACURE® 4167 | King Industries, Inc. | NACURE® 4167 is an amine offset phosphate stimulant. It is an acid stimulant that is fragile and especially effective with polymeric or high imino melamines and phenolics. This product appears as a clear, straw liquid and offers good stability, water resi...view more NACURE® 4167 is an amine offset phosphate stimulant. It is an acid stimulant that is fragile and especially effective with polymeric or high imino melamines and phenolics. This product appears as a clear, straw liquid and offers good stability, water resistance, and solubility. It is soluble in esters, water, ketones, alcohols, glycol ethers, aliphatic and aromatic hydrocarbons. It can be applied in automotive, general industrials, and water-based coatings. view less | |
| NACURE® 4575 | King Industries, Inc. | NACURE® 4575 is an amine offset acid phosphate stimulant suggested for use in coatings that are crosslinked with fully or partially alkylated amino resins. This product offers resistance to coatings exposed to environmental acids, good stability with poly...view more NACURE® 4575 is an amine offset acid phosphate stimulant suggested for use in coatings that are crosslinked with fully or partially alkylated amino resins. This product offers resistance to coatings exposed to environmental acids, good stability with polymetric amino resins, water resistance, and good solubility. It is soluble in alcohols, esters, water, glycol ethers, partially soluble in ketones, and insoluble in aliphatic and aromatic hydrocarbons. NACURE® 4575 appears as a clear, light straw liquid and can be applied in coil coatings and automotive primers, clear coats, and base coats. view less | |
| NACURE® 5076 | King Industries, Inc. | NACURE® 5076 is a strong acid stimulant that is based on Dodecylbenzenesulfonic acid (DDBSA) supplied at 70% active in Isopropanol. This product is soluble in alcohols, glycol ethers, glycols, esters, ketones and aliphatic hydrocarbons. It can also be app...view more NACURE® 5076 is a strong acid stimulant that is based on Dodecylbenzenesulfonic acid (DDBSA) supplied at 70% active in Isopropanol. This product is soluble in alcohols, glycol ethers, glycols, esters, ketones and aliphatic hydrocarbons. It can also be applied in can coatings, paper coatings, and printing inks. view less | |
| NACURE® 5225 | King Industries, Inc. | NACURE® 5225 is an amine counterbalanced Dodecylbenzenesulfonic acid (DDBSA) stimulant and appears as a clear, light color liquid. This product offers good exterior durability, viscosity stability, and broad solubility. It is soluble in aliphatic and arom...view more NACURE® 5225 is an amine counterbalanced Dodecylbenzenesulfonic acid (DDBSA) stimulant and appears as a clear, light color liquid. This product offers good exterior durability, viscosity stability, and broad solubility. It is soluble in aliphatic and aromatic hydrocarbons, alcohol, glycols, glycol ethers, water, ketones, and esters. It can be applied to things such as general industrials, automotive topcoats, and can coatings. view less | |
| NACURE® 5414 | King Industries, Inc. | NACURE® 5414 appears as a clear, amber liquid and is a polymeric blocked sulfonic acid ester stimulant suggested for use with amino crosslinking resins. It can be applied to electrostatic spray applications, automotive topcoats, and general industrials. N...view more NACURE® 5414 appears as a clear, amber liquid and is a polymeric blocked sulfonic acid ester stimulant suggested for use with amino crosslinking resins. It can be applied to electrostatic spray applications, automotive topcoats, and general industrials. NACURE® 5414 offers great intercoat adhesion, better solubility, humidity resistance, and low conductivity that is necessary for electrostatic spray applications. This product is soluble in aliphatic and aromatic hydrocarbons, glycol ethers, glycols, esters, alcohols, and ketones. It is insoluble in water and although it is soluble in alcohols they should be avoided because they may have a negative impact on stimulant stability. view less | |
| NACURE® 5528 | King Industries, Inc. | NACURE® 5528 is an amine blocked Dodecylbenzenesulfonic acid (DDBSA) stimulant that appears as a clear, straw liquid. This product offers good exterior durability, viscosity stability, and broad solubility. It is soluble in aliphatic and aromatic hydrocar...view more NACURE® 5528 is an amine blocked Dodecylbenzenesulfonic acid (DDBSA) stimulant that appears as a clear, straw liquid. This product offers good exterior durability, viscosity stability, and broad solubility. It is soluble in aliphatic and aromatic hydrocarbons, alcohols, ketones, glycol ethers, glycols, esters, and water. NACURE® 5528 is typically applied in can coatings, automotive topcoats, and general industrials. view less | |
| NACURE® 5925 | King Industries, Inc. | NACURE® 5925 is an amine counterbalanced DDBSA stimulant and appears as a clear, light amber liquid. It is made to meet the needs of FDA 21 CFR Section 175.300 (paragraph (b) (3) xiii (a) (b) and xii (a) (b)) concerning chemicals for use in resinous and p...view more NACURE® 5925 is an amine counterbalanced DDBSA stimulant and appears as a clear, light amber liquid. It is made to meet the needs of FDA 21 CFR Section 175.300 (paragraph (b) (3) xiii (a) (b) and xii (a) (b)) concerning chemicals for use in resinous and polymeric coatings. This product offers light color, exterior durability, and good solubility qualities. It is soluble in aliphatic and aromatic hydrocarbons, alcohols, glycol ethers, glycols, esters, ketones, and water. NACURE® 5925 is usually applied in waterborne coatings, automotive topcoats, general industrials, and can coatings. view less | |
| NACURE® 8924 | King Industries, Inc. | NACURE® 8924 is an amine blocked sulfonic acid stimulant that is diluted with water for easier incorporation into water based systems. It appears as a clear, straw liquid, and has good cure response along with solubility in water-based systems. It is solu...view more NACURE® 8924 is an amine blocked sulfonic acid stimulant that is diluted with water for easier incorporation into water based systems. It appears as a clear, straw liquid, and has good cure response along with solubility in water-based systems. It is soluble in alcohols, glycols, glycol ethers, water and is insoluble in ketones, esters, aromatic and aliphatic hydrocarbons. This is a product that is normally applied in water-based coatings, wood coatings, and general industrials. view less | |
| NACURE® CD-2120 | King Industries, Inc. | NACURE® CD-2120 is a proprietary hydrophobic sulfonic acid stimulant. It is effective for the hydrolysis of siloxane functional polymers at ambient conditions. It appears as a dark brown liquid and offers great compatibility with polymers. This product is...view more NACURE® CD-2120 is a proprietary hydrophobic sulfonic acid stimulant. It is effective for the hydrolysis of siloxane functional polymers at ambient conditions. It appears as a dark brown liquid and offers great compatibility with polymers. This product is soluble in ketones, esters, alcohols, glycol ethers, and aliphatic & aromatic hydrocarbons. It can be used as a stimulant for silanol condensation reactions & amino-formaldehyde crosslinkers. It can also be used as an anti-static additive and a pigment dispersant. view less | |
| NACURE® CD-2180 | King Industries, Inc. | NACURE® CD-2180 is a proprietary hydrophobic sulfonic acid stimulant. It is effective for the hydrolysis of siloxane functional polymers at ambient conditions. It appears as a dark brown liquid, cures at ambient circumstances, and offers great compatibili...view more NACURE® CD-2180 is a proprietary hydrophobic sulfonic acid stimulant. It is effective for the hydrolysis of siloxane functional polymers at ambient conditions. It appears as a dark brown liquid, cures at ambient circumstances, and offers great compatibility with polyethylene polymers & copolymers. This product is soluble in ketones, esters, alcohols, glycol ethers, aliphatic & aromatic hydrocarbons, and is insoluble in water. It can be used as a stimulant for silanol condensation reactions & and moisture cure of siloxane. view less | |
| NACURE® X49-110 | King Industries, Inc. | NACURE® X49-110 is an amine neutralized Dinonylnaphthalenesulfonic acid (DNNDSA) stimulant that gives a combination of package stability and cure response. This product offer good adhesion, and resistance to salt spray and humidity. It is soluble in alcoh...view more NACURE® X49-110 is an amine neutralized Dinonylnaphthalenesulfonic acid (DNNDSA) stimulant that gives a combination of package stability and cure response. This product offer good adhesion, and resistance to salt spray and humidity. It is soluble in alcohol, water, glycols, and glycol ethers. It can be applied to automotive primers, general industrials, water based can and coil coatings, electrostatic spray coatings, and electrocoat. view less | |
| NACURE® XC-181 | King Industries, Inc. | NACURE® XC-181 is a latent stimulant based on an alkylaromatic sulfonic acid and appears as a clear, dark liquid. It is made for use in higher bake amino crosslinked structures such as metal decorating and coil coatings, and is also applied in automotive ...view more NACURE® XC-181 is a latent stimulant based on an alkylaromatic sulfonic acid and appears as a clear, dark liquid. It is made for use in higher bake amino crosslinked structures such as metal decorating and coil coatings, and is also applied in automotive topcoats and appliance finishes. It offers overbake resistance, “solvent pop” resistance, solubility in non-polar solvents and it is amine free. This product is soluble in aliphatic and aromatic hydrocarbons, alcohols, esters, ketones and glycol ethers. it is insoluble in water and glycols. view less | |
| NACURE® XC-235 | King Industries, Inc. | NACURE® XC-235 is an acid phosphate stimulant supplied at 75% active in n-butanol. It is recommended to be used with high amino or somewhat alkylated type melamine crosslinkers. This product is soluble in alcohol, glycols, ethers, and is not soluble in wa...view more NACURE® XC-235 is an acid phosphate stimulant supplied at 75% active in n-butanol. It is recommended to be used with high amino or somewhat alkylated type melamine crosslinkers. This product is soluble in alcohol, glycols, ethers, and is not soluble in water. It offers good cure response and humidity resistance. It can be applied to topcoatings, primers, and wood coatings. view less | |
| NACURE® XC-300 | King Industries, Inc. | NACURE® XC-300 is a covalently blocked stimulant that is based on an alkylaromatic sulfonic acid. It is made to offer enhanced support in amino crosslinked primers that engage basic or ion exchange type anti-corrosive pigments. This product is soluble in ...view more NACURE® XC-300 is a covalently blocked stimulant that is based on an alkylaromatic sulfonic acid. It is made to offer enhanced support in amino crosslinked primers that engage basic or ion exchange type anti-corrosive pigments. This product is soluble in aliphatic and aromatic hydrocarbons, esters, alcohol, and ketones. It is designed to be applied to appliance finish primers, general industrial thermoset primers, and coil coating primers. view less | |
| NACURE® XC-311 | King Industries, Inc. | NACURE® XC-311 appears as a clear and transparent light amber liquid. It is a novel latent acid stimulant that is made to reduce the cure temperature of amino crosslinked systems. This product offers good salt spray, humidity, QUV, and overbake resistance...view more NACURE® XC-311 appears as a clear and transparent light amber liquid. It is a novel latent acid stimulant that is made to reduce the cure temperature of amino crosslinked systems. This product offers good salt spray, humidity, QUV, and overbake resistance. It is soluble in aliphatic and aromatic hydrocarbons, alcohol, glycol ethers, ketones, and water. It is designed to be applied to metal decorating, coil coatings, appliance finishes, and OEM coatings. view less | |
| NACURE® XP-379 | King Industries, Inc. | NACURE® XP-379 appears as a clear, straw liquid and is an amine blocked Dodecylbenzenesulfonic acid (DDBSA) stimulant supplied in Isopropanol. It offers exterior durability, viscosity stability, and broad solubility. This product is soluble in aliphatic a...view more NACURE® XP-379 appears as a clear, straw liquid and is an amine blocked Dodecylbenzenesulfonic acid (DDBSA) stimulant supplied in Isopropanol. It offers exterior durability, viscosity stability, and broad solubility. This product is soluble in aliphatic and aromatic hydrocarbons, alcohols, glycol ethers, glycols, esters, ketones, and water. NACURE® XP-379 can be applied to general industrials, automotive topcoats, and can coatings. view less | |
| Octaflow ST-70 | Estron Chemical, Inc. | Octaflow ST-70 is the tin-based liquid catalyst stannous octoate adsorbed onto a silica carrier. The additive may be used in both e-caprolactam blocked polyurethane powder coatings and the internally blocked uretdione systems. Octaflow ST-70 is incorporat...view more Octaflow ST-70 is the tin-based liquid catalyst stannous octoate adsorbed onto a silica carrier. The additive may be used in both e-caprolactam blocked polyurethane powder coatings and the internally blocked uretdione systems. Octaflow ST-70 is incorporated as a raw material during the premix stage of processing. view less | |
| POLYCAT® DBU | Evonik Operations GmbH, BL Comfort & Insulation | POLYCAT® DBU is a strong gel catalyst that provides snap cure at ambient temperature. | |
| POLYCAT® SA 1/10 | Evonik Operations GmbH, BL Comfort & Insulation | POLYCAT® SA 1/10 is an acid-free heat activated catalyst that provides excellent back-end cure. Can provide an extended pot life. It stays liquid at low temperature. | |
| POLYCAT® SA 2 LE | Evonik Operations GmbH, BL Comfort & Insulation | POLYCAT® SA 2 LE is a low emission heat activated catalyst that exhibits a front end delay with rapid back end-cure. | |
| POLYCAT® SA 20 | Evonik Operations GmbH, BL Comfort & Insulation | POLYCAT® SA 20 is a DBT-free low emission gelling catalyst that gives a back-end cure similar to a tin catalyst and a similar working time as an amine catalyst. | |
| POLYCAT® SA 4 | Evonik Operations GmbH, BL Comfort & Insulation | POLYCAT® SA 4 is a heat activated catalyst that provides excellent back-end cure. Can provide an extended pot life. It stays liquid at low temperature. Is has higher de-blocking temperature and longer pot life time than POLYCAT® SA 1/10. | |
| POLYCAT® SA 5 | Evonik Operations GmbH, BL Comfort & Insulation | POLYCAT® SA 5 is a gelling catalyst that gives a back-end cure similar to a tin catalyst and a similar working time as an amine catalyst. It is recommended to use in conjunction with DABCO® BA 100 to improve pot life time. | |
| POLYCAT® SA 8 | Evonik Operations GmbH, BL Comfort & Insulation | POLYCAT® SA 8 is a heat activated co-catalyst with an excellent front-end delay. | |
| Potassium Octoate (EGECat Potassium 15%) | EGE Kimya San ve Tic A.S. | Potassium Octoate (EGECat Potassium 15%) is an effective promoter with cobalt octoate used in low color applications. This product is soluble in organic solvents and oils, and it has a potassium metal content of 15% and a total solids content of 80%. | |
| Provichem 1102 | Proviron | Provichem 1102 is a very effective trimerization catalyst for the preparation of rigid polyisocyanurate foams. This low odour catalyst is free of amino-groups and glycol solvents. | |
| PTSC | Axcentive Sarl | PTSC stands for para toluene sulfonylchloride also named tosylchloride or abbreviated TsCl. It serves as intermediate in pharmaceutics and in various chemical synthesis. This product can be used as an acid catalyst in thermosetting resins and as a blockin...view more PTSC stands for para toluene sulfonylchloride also named tosylchloride or abbreviated TsCl. It serves as intermediate in pharmaceutics and in various chemical synthesis. This product can be used as an acid catalyst in thermosetting resins and as a blocking agent to protect hydroxyl groups during reactions. view less | |
| PVB | Beijing Entrepreneur Science &Trading Co., Ltd. | Polyvinyl butyral (PVB) with hydrochloric acid as catalyst, is made from polyvinyl alcohol and butyl aldehyde. The abbreviate is PVB. High gloss, high transparent, non-toxic, smell-less, fast dissolve, etc. It’s good soluble with pigments and dyes. The PV...view more Polyvinyl butyral (PVB) with hydrochloric acid as catalyst, is made from polyvinyl alcohol and butyl aldehyde. The abbreviate is PVB. High gloss, high transparent, non-toxic, smell-less, fast dissolve, etc. It’s good soluble with pigments and dyes. The PVB has high transparency, good cold resistance, water resistance, film forming properties and impact resistance, widely used in middle film of glass, ceramic flower paper, metal protective paint, tipping paper, aluminum foil, insulation paint, fiber treatment agent, finished parts, printing inks, dyes and so on. view less | |
| Spolapon CS | Enaspol AS | Spolapon CS is a cumenesulfonic acid catalyst with a pasty yellow liquid appearance that is used in environments where strong acid is required. This product is used in esterfication processes and emulsion breaking as well as polymer reactions in coatings ...view more Spolapon CS is a cumenesulfonic acid catalyst with a pasty yellow liquid appearance that is used in environments where strong acid is required. This product is used in esterfication processes and emulsion breaking as well as polymer reactions in coatings and the cross-linking of adhesives. view less | |
| Spolapon XS | Enaspol AS | Spolapon XS is a xylenesulphonic acid catalyst with a light brown liquid appearance that is used in environments where strong acid is required. This product is used in esterfication processes and emulsion breaking as well as polymer reactions in paints or...view more Spolapon XS is a xylenesulphonic acid catalyst with a light brown liquid appearance that is used in environments where strong acid is required. This product is used in esterfication processes and emulsion breaking as well as polymer reactions in paints or coatings and the cross-linking of adhesives. view less | |
| Tetra-Isopropyl Titanate | Anhui Taichang Chemical Co., Ltd. | Tetra-Isopropyl Titanate is an intermediate derived from titanium. This product appears as a light yellow, transparent liquid. It can be used as a catalyst additive in coating primers or added to that formulation as an adhesion promoter. | |
| Tetrafluoroboric Acid 50% | Büfa Chemikalien GmbH & Co.KG | Tetrafluoroboric Acid 50% is a clear liquid with a product specific odor. | |
| TIB KAT® 129 | TIB Chemicals | TIB KAT® 129 is a liquid catalyst that distributes well in reactants. It is used for esterifications in oleochemistry, catalysis or polyurethane systems, curing of silicone resins and silanes and for polymerisation of lactones to biodegradable polymers. | Request Sample |
| TIB KAT® 160 | TIB Chemicals | TIB KAT® 160 is a catalyst that is used in the production of organic esters and plasticizers. It possesses a high level of catalytic activity which leads to almost complete conversions with short reaction times at higher reaction temperatures (> 160°C). T...view more TIB KAT® 160 is a catalyst that is used in the production of organic esters and plasticizers. It possesses a high level of catalytic activity which leads to almost complete conversions with short reaction times at higher reaction temperatures (> 160°C). This product also enables the production of light-coloured esters. Secondary reactions do hardly occur in comparison to acidic catalysts. view less | Request Sample |
| TIB KAT® 162 | TIB Chemicals | TIB KAT® 162 is a catalyst that is used in the production of polyesters and oleochemical-based esters. It is also used as an activator in the production of elastomers. This product is soluble in water and a number of non-aqueous polar solvents. During the...view more TIB KAT® 162 is a catalyst that is used in the production of polyesters and oleochemical-based esters. It is also used as an activator in the production of elastomers. This product is soluble in water and a number of non-aqueous polar solvents. During the esterification process, it minimises the dehydration of alcohols and avoids odours and discolouration of the products which can be formed by possible by- products. view less | Request Sample |
| TIB KAT® 188 | TIB Chemicals | TIB KAT® 188 is a free-flowing, dry, stable tin(II) oxide which has excellent catalytic properties as an esterification catalyst. The quantities of this product to be added for esterification are generally between 0.01 and 0.10 wt.-%. TIB KAT 188 shows th...view more TIB KAT® 188 is a free-flowing, dry, stable tin(II) oxide which has excellent catalytic properties as an esterification catalyst. The quantities of this product to be added for esterification are generally between 0.01 and 0.10 wt.-%. TIB KAT 188 shows the highest catalytic activity at reaction temperatures between 180 - 260°C. view less | Request Sample |
| TIB KAT® 208 | TIB Chemicals | TIB KAT® 208 is a liquid organotin catalyst dissolved in a special solvent. It is advantageous for the production of coatings based on polyurethanes and is suitable for the condensation of silicones. | Request Sample |
| TIB KAT® 214 | TIB Chemicals | TIB KAT® 214 is a versatile tin mercaptide catalyst that can be used in various polyurethane coatings formulations that demand hydrolytic stability and selectivity. It has higher hydrolytic stability than comparable organotin carboxylates. The catalytica...view more TIB KAT® 214 is a versatile tin mercaptide catalyst that can be used in various polyurethane coatings formulations that demand hydrolytic stability and selectivity. It has higher hydrolytic stability than comparable organotin carboxylates. The catalytical reactivity of this product in polyurethane systems is in most cases higher than DBTL (TIB KAT® 218), resulting in shorter pot life and quicker curing times. The use in water-based systems is possible within certain limits. view less | Request Sample |
| TIB KAT® 216 | TIB Chemicals | TIB KAT® 216 is a liquid tin catalyst based on dioctyltin compounds. It provides improved toxicological properties and is used in the curing of silicone resins, catalysis of polyurethane resins, transesterification and esterification reactions as a stabil...view more TIB KAT® 216 is a liquid tin catalyst based on dioctyltin compounds. It provides improved toxicological properties and is used in the curing of silicone resins, catalysis of polyurethane resins, transesterification and esterification reactions as a stabilizer for PVC. view less | Request Sample |
| TIB KAT® 217 | TIB Chemicals | TIB KAT® 217 is a liquid catalyst based on a dioctyltinoxide formulation. It can be applied for the curing of silicones and silane systems. | Request Sample |
| TIB KAT® 218 | TIB Chemicals | TIB KAT® 218 is a catalyst that can be used in esterification and transesterification reactions. It is also used in the reaction between isocyanates and alcohols. This product is suitable for can and coil coatings, elastomers, car refinishing, architectur...view more TIB KAT® 218 is a catalyst that can be used in esterification and transesterification reactions. It is also used in the reaction between isocyanates and alcohols. This product is suitable for can and coil coatings, elastomers, car refinishing, architectural, and other industrial coatings; and for 1p/2p adhesives and sealants.. view less | Request Sample |
| TIB KAT® 220 | TIB Chemicals | TIB KAT® 220 is a liquid catalyst that is used in the production of plasticizers, saturated and unsaturated polyesters and in the curing of polyurethane based powder coatings. This product has a tin content of 18.8-20.6%. | Request Sample |
| TIB KAT® 223 | TIB Chemicals | TIB KAT® 223 is a liquid Dioctyltin based catalyst, which has been developed especially for 1K MS silyl systems. It is also suitable for polycondensation reactions of RTV silicone resins and silane terminated polymers as well as for the synthesis of Polyu...view more TIB KAT® 223 is a liquid Dioctyltin based catalyst, which has been developed especially for 1K MS silyl systems. It is also suitable for polycondensation reactions of RTV silicone resins and silane terminated polymers as well as for the synthesis of Polyurethane-systems. TIB KAT® 223 shows a lower toxic potential compared to Dibutyltin catalysts and can replace these. view less | Request Sample |
| TIB KAT® 225 | TIB Chemicals | TIB KAT® 225 is a catalyst for use in various applications such as esterification and transesterification reactions as well as the condensation of silicones and silanes, especially for the production of RTV silicone resins. This product is less sensitive ...view more TIB KAT® 225 is a catalyst for use in various applications such as esterification and transesterification reactions as well as the condensation of silicones and silanes, especially for the production of RTV silicone resins. This product is less sensitive to moisture than other types of DBTL. view less | Request Sample |
| TIB KAT® 226 | TIB Chemicals | TIB KAT® 226 is a catalyst for the synthesis of polyurethane systems, polycondensation reactions of RTV silicon resins and silanes and for 1 K MS silyl systems. It is miscible with organic solvents, but sensitive to moisture and frost. | Request Sample |
| TIB KAT® 226 V80 | TIB Chemicals | TIB KAT® 226 V80 can be used as a catalyst for 1 K MS Silyl systems, polycondensation reactions of RTV silicon resins and silanes, and synthesis of polyurethan-systems. This product is delivered in liquid form and is miscible with organic solvents, but is...view more TIB KAT® 226 V80 can be used as a catalyst for 1 K MS Silyl systems, polycondensation reactions of RTV silicon resins and silanes, and synthesis of polyurethan-systems. This product is delivered in liquid form and is miscible with organic solvents, but is sensitive to moisture. view less | Request Sample |
| TIB KAT® 229 | TIB Chemicals | TIB KAT® 229 is suitable to replace TIB KAT 223 and as a catalyst for synthesis of polyuretane-systems, transesterification, polycondensation reactions of RTV silicon resins and silanes, and production of raw materials for polycarbonates. This product is ...view more TIB KAT® 229 is suitable to replace TIB KAT 223 and as a catalyst for synthesis of polyuretane-systems, transesterification, polycondensation reactions of RTV silicon resins and silanes, and production of raw materials for polycarbonates. This product is slightly sensitive to moisture. view less | Request Sample |
